Sony SRX-R220 User Manual
Page 14
14
Specifications (SRX-R220/SRX-R210)
SXRD Device Main Specifications
Display device
SXRD (Silicon X-tal Reflective Display)
Size
1.55-inch across Diagonal
Resolution
4096 (H) X 2160 (V) Pixels
Reflectivity
77%
Contrast
More than 4000:1
Pixel pitch
8.5 μm
Width (between pixels)
0.35 μm
Response speed
5 msec (tr + tf)
Liquid crystal mode
Vertical Aligned Mode
Alignment layer
Inorganic Thin Film
Backplane process
0.35 μm MOS Process
Liquid crystal cell gap
Less than 2 μm
Optical
Projection system
3-SXRD panel, prism color integrated system
Imaging device
SXRD, 1.55-inch (diagonal),
4096 (H) x 2160 (V) pixels on each chip
Lamp
SRX-R220: 4.2 kW Xenon lamp x 1
SRX-R210: 3.0 kW** Xenon lamp x 1 or
2.0 kW** Xenon lamp x 1
Screen coverage
SRX-R220: 4.5-meter to 20-meter screen width on
(Approx.)
Scope size (4.2 kW lamp)
SRX-R210: 4.5-meter to 17-meter screen width on
Scope size (3.0 kW lamp)**
4.5-meter to 14-meter screen width on
Scope size (2.0 kW lamp)**
Light output
SRX-R220: 14ft-L on 20-meter wide screen
(4.2 kW lamp)*
SRX-R210: 14ft-L on 17-meter wide screen
(3.0 kW lamp)* **
14ft-L on 14-meter wide screen
(2.0 kW lamp)* **
General
Colorimetry
Xenon Color Primaries
Encoding Primaries
X
Y
R
0.6800 0.3200
G
0.2650 0.6900
B
0.1500 0.0600
White reference
Xenon white reference
X
Y
White reference
0.3140
0.3510
Contrast
Over 2000:1
Input signal
Media Block input x 2: 4096 x 2160 pixels
HD-SDI/Dual-link HD-SDI: 1920 x 1080 pixels
(SMPTE-372M/SMPTE-292M/ITU-R.BT709/BTA-S004)
DC-SDI/Dual-link DC-SDI: 2048 x 1080 pixels
12 bit/X’Y’Z’
(with Dual-link HD/DC-SDI Input Board)
DVI-D: XGA (1024x768) / SXGA1 (1280x960) /
SXGA2 (1280x1024) / SXGA+ (1400x1050) /
UXGA (1600x1200) / WUXGA (1920x1200) /
HD (1920x1080) / DC (2048x1080)
Power consumption
SRX-R220: 1.2 kW (Single-phase/100-240VAC for
main circuit) / 5.2kW (3-phase/
200-208VAC or 380-415VAC selectable
for lamp)
SRX-R210: 1.2kW (Single-phase/100-240VAC for
main circuit) / 3.4kW** (3-phase/
200-208VAC or 380-415VAC selectable
for lamp)
Power requirements
AC 100 to 240 V, 50/60 Hz, single-phase
(for Main power)
AC 200 to 208 V / AC 380 to 415 V,
3-phase(changeable) , 50/60 Hz (for Lamp power)
Operating temperature
+5°C to +35°C (+41°F to +95°F)
Storage temperature
-20°C to +60°C (+12°F to +140°F)
Operating humidity
35% to 85% (without condensation)
Storage humidity
10% to 90%
Dimensions
740 x 1535 x 1395mm
(W x H x D)
(29 1/4 x 60 1/2 x 55 inches)
Mass
300 kg (661 lb 6 oz), without lens and lamp
Fan noise
65 dB or less
* Measured at the screen center of a full pixel size (4096 x 2160) projection with 100 IRE
white and a screen gain of 1.8. A ft-L (foot-lambert) is a unit of measurement for
luminance. One foot-lambert equals 3.4262591 candelas per square meter.
** Tentative