Programming the playing order of the tracks, Random play repeating tracks – JVC UX-MD9000R User Manual

Page 16

English

You can program the playing order of the tracks using the Remote
Control.

■

You can program up to 20 tracks in any desired order including
the same tracks.

■

You can only make a program when the CD Player is stopped.

■

1. Insert a CD.

■

2. Press the CD

38 button.

■

3. Press the

7 button to stop the CD.

■

4. Press the PROGRAM button.

The System enters the programming mode and the “CD PRO-
GRAM” indicator lights up.

■

5. Press the UP, DOWN, >, or < button to

select the track to program.

UP button:

Increases the track number by 1.

DOWN button: Decreases the track number by 1.
>

button:

Increases the tenth digit of the track number.

< button:

Decreases the tenth digit of the track number.

•

Example: for track 2, press the UP button twice. For track 12,
press the > button, then press the UP button twice (or simply
press the UP button 12 times).

■

6. Press the SET button.

■

7. Repeat steps 5 and 6 to select the other

tracks for the program.

You can see the total playback time of programmed tracks on
the display. Also, you can see the programmed tracks on the
music calender.

■

8. Press the CD

button.

The System plays the tracks in the order you have programmed
them.

■

You can skip to a particular program track by pressing the

button during Program Play.

■

To stop playing, press the

button once.

To confirm the programmed tracks while the CD player is
stopped,

press the

button; the tracks making up the

program will successively be displayed in the programmed order.

To delete all the tracks in the program,

press the

button re-

peatedly until all the tracks are cleared. Turning off the power or
pressing the CD

button to open the CD holder will also clear the

programmed tracks.

To exit the program mode once,

while the CD Player is

stopped, press the PROGRAM button to light off the "CD PRO-
GRAM" indicator.

Note:

If the total playback time of the programmed tracks exceeds
99 minutes 59 seconds, the total playback time will go out
on the display.

To Modify the Program ———————

Modify the contents of the program while the CD Player is stopped.
Each time you press the

button, the last track in the program is de-

leted. To add new tracks to the end of the program, repeat above
steps 5 to 7.

The tracks will play in no special order when you use this mode.

■

1. Press the RANDOM button on the Remote

Control.

The "CD RANDOM" indicator lights up on the display.

■

2. Press the CD

button.

The tracks are played in random order.

To skip a track during playback,

press the

button to jump

to the next track in the random sequence. Press the

button to

jump back to the start of a track being played.

To exit Random Play mode,

press the RANDOM button to light

off the "CD RANDOM" indicator and carry out Normal Play or
Program Play, or press the CD

button to open the CD holder.

You can set the program or individual track playing to repeat as
many times as you like.

Press the REPEAT button on the Remote Control.

The Repeat indicator changes with each press of the button, as
shown below.

ALL

blank display

(back to the beginning)

: Repeats one track.

ALL

: In Normal Play mode, repeats all the tracks.

In Program Play mode, repeats all the tracks in the
program.
In Random Play mode, repeats all the tracks in ran-
dom order.

To exit Repeat mode,

press the REPEAT button until the Repeat

indicator on the display goes out.

■

In Random Play, as a matter of course,

cannot be selected.

■

Repeat mode remains on the display even when you change the
play mode.

Programming the
Playing Order of the Tracks

PROGRAM

DOWN

SET

Program order number

Total playback time of the programmed tracks

(After 2 seconds)

Random Play

Repeating Tracks

Ux-MD9000-e.fm Page 12 Tuesday, June 23, 1998 9:38 AM