JVC DR-MV5BEK - Manual (Page 59)

Masterpage:Right+
EN
59
Filename [MV5SEK_09Advanced Operation.fm]
ADVANCED PLAYBACK
Page 59Wednesday, 31 August 2005 19:58
Still Picture/Frame-By-Frame Playback
1
Press 9 to pause during playback.
● If there is vertical jitter, press PR +/– to correct the picture.
2
Press 9 repeatedly to activate frame-by-frame playback.
● To resume normal playback, press 4.
Slow Motion
1
Press 9 to pause during playback.
2
Press and hold 9 for 2 seconds, then release. Press 9 and
release again to return to still picture.
● To resume normal playback, press 4.
NOTE:
During slow motion playback, some noise may appear on the TV
screen. Press PR + or – to eliminate the noises.
High-Speed Search
During playback, press 5 for forward high-speed search, or
3 for reverse high-speed search.
● Each press of the button increases the search speed for each
direction.
When pressing 5:
(SP): +5x{+7x
(LP): +11x{+21x
When pressing 3:
Once 3 is pressed, reverse search starts in –1x normal playback
speed. After this process, each press of 3 changes the search
speed between –5x and –7x in SP mode, –11x and –21x in LP mode.
(SP): –1x]–5x{–7x
(LP): –1x]–11x{–21x
● To resume normal playback, press 4.
Quick Rewind A Little
During playback, press . The unit rewinds the picture a little
(about 7 seconds) and resumes playback.
● If the button is pressed repeatedly, the unit rewinds the pictures
continuously and resumes playback.
Skip Search
During playback, press 1 to 6 times to skip over unwanted
sections.
● Each press initiates an approximately 30-second period of fast-
motion playback. Normal playback resumes automatically.
● To resume normal playback, press 4.
Index Search
Your unit automatically marks index codes at the beginning of each
recording. This function gives you quick access to any one of the 9
index codes in either direction.
NOTE:
Before starting, make sure the unit is in the Stop mode.
Press 2 or 6 to activate Index Search. “2 1” or “6 1” is
displayed on the TV screen and search begins in the corresponding
direction.
● To access index codes 2 through 9, press 2 or 6 repeatedly
until the correct index number is displayed.
Example:
To locate the beginning of B from the current position, press 2
twice.
To locate the beginning of D from the current position, press 6
once.
● When the specified index code is located, playback begins
automatically.
Advanced Playback (VHS)
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/DVD switch to DVD.
● Press VHS so that the VHS lamp lights up on the unit.
Clean the video heads using a dry cleaning cassette when:
● Rough, poor picture appears while a tape is played back.
● The picture is unclear or no picture appears.
● “USE CLEANING CASSETTE” appears on the screen (only with
“SUPERIMPOSE” set to “AUTO”). ( ੬ pg. 79)
NOTE:
The heads get dirty in the following cases:
● in an environment prone to extreme temperature or humidity
● in a dusty environment
● flaw, dirt or mold on video tapes
● continuous usage for a long time
ATTENTION:
In the search, still, slow-motion or frame-by-frame playback mode,
● the picture will be distorted.
● the noise bars will appear.
● there may be a loss of colour.
● you cannot hear the sound.
PR +/–
VHS
Index number
Current position
MV5SEK_00.book Page 59 Wednesday, August 31, 2005 7:58 PM