JBL CS3 - Manual (Page 26)

TV Menu
As a Scart audio/video cable contains both audio and video inputs
and outputs in one cable, the Scart connector between the DVD
Receiver and the TV can also be used to lead the audio output sig-
nals of your TV to the DVD receiver. In this way your TV programs
can be listened to over your CS sound system.
NOTE: Please make sure that the Scart cable used has all pins
connected. If not it could be that, only the video signal from the
DVD receiver will be lead to the TV.
1. Press the TV 0 button on the remote control to turn the DVD
receiver on and select TV as the source. Also make sure that
your video monitor connected to the CS3/CS5 is switched on.
2. The TV monitor will show the TV menu, as shown below. You can
also select the TV menu with the Arrow
9 keys on the remote
control. Once the TV tab is highlighted, press Enter 6 to access it.
If the CS receiver is already in Standby, you can also switch the
unit on by pressing the TV button on the remote control.
The TV menu contains the following settings. Follow the expla-
nations in the Upper Menu Line on the bottom of your screen to
change the settings.
Audio: Selects the surround mode you would like to use when
listening to your TV or other video device connected to the SCART
input.
Level Adjustment: This setting gives you the possibility to increase
or decrease the input level of the TV, so that its sound will have the
same level as the radio, the DVD player or the other audio inputs.
AUX Menu
In addition to the built-in DVD-Audio/Video and CD player, the built-
in radio and SCART audio input, you can connect one more analog
audio source to the CS3/CS5. The analog source can be connected
to the Audio In Input
6 connectors on the rear panel.
1. Press the AUX
0 button on the remote control to turn the DVD
receiver on and select AUX as the source. Also make sure that
your video monitor connected to the CS3/CS5 is switched on.
2. The TV monitor will show the AUX menu. You can also select the
AUX menu with the Arrow 9 keys on the remote control. Once
the A U X tab is highlighted, press Enter 6 to access it.
The AUX menu contains the following settings. Follow the
explanations in the Upper Menu Line on the bottom of your screen
to change the settings.
Audio: Selects the surround mode you would like to use when
listening to your additional analog audio source.
Level Adjustment: This setting gives you the possibility to increase
or decrease the input level of the analog input, so that its sound
will have the same level as the radio, the DVD player or the other
audio inputs.
Digital In Menu
In addition to all analog audio and video sources, the CS3/CS5 also
gives you the opportunity to connect two digital audio sources, for
instance a digital set-top box or satellite receiver. Connect these
sources to either the coaxial or optical digital input connectors on
the rear panel.
1. Press the D.IN 0 button on the remote control to turn the DVD
receiver on and select Digital In as the source. Also make sure
that your video monitor connected to the CS3/CS5 is switched on.
2. The TV monitor will show the Digital In menu, as shown below.
You can also select the Digital In menu with the Arrow 9 keys
on the remote control. Once the D . I N tab is highlighted, press
Enter 6 to access it.
The Digital In menu contains the following settings. Follow the
explanations in the Upper Menu Line on the bottom of your screen
to change the settings.
Digital Input: Selects either the digital source connected to the
coaxial or to the optical digital input as source to listen to.
Audio: Selects the surround mode you would like to use when
listening to one of the digital audio sources.
Level Adjustment: This setting gives you the possibility to increase
or decrease the input level of the digital input, so that its sound will
have the same level as the radio, the DVD player or the other audio
inputs.
26
TV MENU, AUX MENU, DIGITAL IN MENU