JVC RS-WP1WT - Manual (Page 14)

English
11
To stop playing the CD, press the 7 button.
The following information for the CD is displayed.
To pause, press the CD 6 button. The playback time blinks on
the display.
To cancel pause, press the same button again. Play continues
from the point where it was paused.
Note:
Do not open the CD cover during playback.
Locating a Track with Remote
Control Directly —————————
During playback or in Stop mode, press the number keys on the
Remote Control to directly play a track.
To directly play the track 5, press 5.
To directly play the track 15, press +10 then 5.
To directly play the track 20, press +10 once then press 10.
A.S.P. (Anti-Shock Protection)
To minimize skipping of audio due to vibrations, all audio data (for
up to 40 sec.) is stored in the buffer so as to use it in case audio
skipping is going to occur.
To enable A.S.P.:
Press the ASP button during stop or playback so that the “ASP”
indicator appears in the display.
To disable A.S.P.:
Press the ASP button again so that the “ASP” disappears from the
display.
Notes:
•
When the A.S.P. function is enabled, the audio data in the CD
section to be played is read in advance with a rotation speed
which is slightly higher than the standard speed, and stored in a
buffer. As a result, this causes the battery power to consume
faster than usual.
• Every time the ASP button is pressed, the played sound is
interrupted. However, this is due to the change in the rotation
speed and not a malfunction.
• The sound may skip at high volume levels if the disc is scratched
or stained or depending on the recorded signal. In such a case,
switch the A.S.P. function ON.
You can use Normal, Program, Random or Repeat Play. Repeat Play
can repeat all the tracks or just one of the tracks on the CD.
Here are the basic things you need to know to play a CD and locate
the different tracks on it.
The Quickest Way To Start a CD Is With the One
Touch Operation (effective only when the System
is operated on AC power or car battery (DC12V))
■
Press the CD 6 button.
• The power is automatically turned on. If a CD is already
inserted, it will start playing from the first track.
• If no CD is inserted, “NO DISC” appears on the display and the
CD Player remains in Stop mode.
• When the System is operated on batteries, press the
STANDBY/ON button on the Unit before operation.
Setting a CD
1. Turn the door knob counterclockwise to open
the door.
2. Hold the CD with its label side as shown below
and push fit it in place until it clicks.
3. Close the door until it clicks.
To remove the CD, open the door in Stop mode.
■
You can place an 8 cm (3”) CD without an adaptor.
■
If the CD cannot be read correctly (because it is scratched, for
example), “no disc” appears on the display.
■
You can place a CD while listening to the other source.
Basics of Using the
CD Player-Normal Play
To Play a CD ——————————
1. Set a CD.
2. Press the CD 6 button.
The first track of the CD begins playing.
• The CD Player automatically stops when the last track of the CD
has finished playing.
Using the CD Player
TRACK ALL PRGM RND ASP
TRACK
TRACK
SLEEP
CLOCK TIMER
TIMER
ON/OFF
PROGRAM
RANDOM
REPEAT
BAND
DISPLAY
AHB PRO
REVERSE MODE MULTI CONTROL
FM MODE
REW FF
RM-SRSWP1U REMOTE CONTROL
TAPE TUNER C D
DOWN UP SET
AUX
VOLUME
BASS/
TREBLE
STAND BY/ON
AUTO PRESET
PROGRAM
RANDOM
REPEAT
7
¢
6
4
CD
Number
keys Track number, Playing time,
Preset number
Play mode indicator Repeat
indicator
Total track
number Total playing time
ASP
indicator
When the System is in use, the display shows
other items as well.
For simplicity, we show here only the items
described in this section.
VOLUME
VOLUME
AUX
TU NE R
TA PE
CD
ASP
O P EN
O N E TO UCH R E C
MULTI CONTROL
REW FF
STANDBY
CD PORTABLE SYSTEM RS-WP1
BAND
STANDBY/ON
¢
4
7
6 CD
A .P.OFF
ASP
Door knob