Infinity TSS 3-IN-1 - Manual (Page 2)

25
7
8
2
22
18
3
1
11
10
6
4
5
12
13
15
17
24
23
9
19
20
14
16
TSS 3-IN-1
EXPLODED VIEW
ITEM
NO.
DESCRIPTION QTY. PART NO.
1. Aluminum cabinet 1 Not For Sale
2. Plastic front baffle (Platinum) 1 FA-80317-02
Plastic front baffle (Charcoal) 1 FA-80317-01
3. Top/bottom cap (Platinum) 1 FE-80312-02
Top/bottom cap (Charcoal) 1 FE-80312-03
4. Plastic inner cover 1 Not For Sale
5. Wall-mount end caps, small (Platinum) 2 BP1-80312-02
Wall-mount end caps, small (Charcoal) 2 BP1-80312-04
6. Wall-mount end caps, large (Platinum) 2 BP2-80312-03
Wall-mount end caps, large (Charcoal) 2 BP2-80312-05
7. Front grille (Platinum) 1 NT-80317-02
Front grille (Charcoal) 1 NT-80317-01
8. Front grille gasket 2 PK-0106-01
9. Crossover network (Platinum) 3 FL-80305-01MS
Crossover network (Charcoal) 3 FL-80305-01MBS
10. Speaker base (Platinum) 1 SP-80317-02
Speaker base (Charcoal) 1 SP-80317-01
11. Speaker-base gasket (Platinum) 1 PK-0107-02
Speaker-base gasket (Charcoal) 1 PK-0107-01
12. Wall-bracket cover (Platinum) 1 SP-80317-03
Wall-bracket cover (Charcoal) 1 SP-80317-01
13. Main wall bracket (Platinum) 1 SP-80317-04
Main wall bracket (Charcoal) 1 SP-80317-02
14. Screw, woofer M4*7 24 SR-2104-07
15. Screw, terminals M3.5*12 (Platinum) 12 SR-2435-12
Screw, terminals M3.5*12 (Charcoal) 12 SR-2435-12B
16. Screw, tweeter M3.5*10 6 SR-0535-10
17. Screw, wall bracket M4*18 (Platinum) 4 SR-0304-18
Screw, wall bracket M4*18 (Charcoal) 4 SR-0304-18A
18. Screw, top cap M6*18 (Platinum) 2 SR-1006-18
Screw, top cap M6*18 (Charcoal) 2 SR-1006-18A
19. 3.5" Woofer 6 080F30004
20. 3/4" Tweeter 3 020D30901
21. Hex wrench 1 HW-4001-01
22. Gasket, front baffle 3 PK-80311-02
23. Gasket, network 3 PK-80307-01
24. Gasket, wall bracket (Platinum) 4 PK-1019-01
Gasket, wall bracket (Charcoal) 4 PK-1019-02
25. Logo 1 AL-80305-01
26. Outer carton (Platinum) 1 BO-80317-01
Outer carton (Charcoal) 1 BO-80317-03
27. Packing polyfoam, set complete 1 PO-80317-01/2/3
28. Owner’s manual 1 ML-80317-01
29. Warranty card 1 WC-TSS4000-01
Technical Manual
TSS 3-IN-1
TO SERVICE THE TSS 3-IN-1
1. Remove both end caps with a 4mm or 5-32" Allen wrench (hex key).
2. Gently pull up the metal grille from one end, and remove grille.
3. Remove the plastic front baffle by using a small screwdriver on one corner of the front baffle and lifting the baffle corner
away from the cabinet (see illustration).
4. Once one corner is lifted away, reach under the front baffle to pull and extract both sides of the front baffle from the
cabinet, on that end. This is complicated by the fact that three tweeters, bolted to the front baffle, are also attached with
adhesive, so each bead must be carefully broken.
5. CAUTION: Once the baffle starts to separate from the cabinet, do not lift the baffle too high off the cabinet and attempt
to remove it; the tweeter wires – three sets – are attached. The tweeter wire clips must be detached from the tweeters
as the baffle is removed.
6. Once the front baffle is removed, all drivers are exposed for servicing. The crossover network(s) is attached to the inside of the cabinet,
and woofers may need to be removed to replace the network(s).
7. Upon reassembly, there should still be enough adhesive left on the baffle to reattach it to the cabinet face; if not, apply a light coating of
contact cement, silicone seal, or similar adhesive to the surfaces around the tweeters.
3/07 Infinity Systems, 250 Crossways Park Drive, Woodbury, New York 11797