Ikelite DSC-W200 - Manual (Page 2)

LLeennss PPoorrtt
Treat the glass in the lens port as a camera lens. After use, rinse
and gently dry the lens port to avoid water spotting. To clean
use a mild soap solution or lens cleaner.
Do not use alcohol or window cleaner on the Lens Port.
The Lens Port will accept (2) Wide-Angle Adapters. The Wide-
Angle Adapter #9306.80 which is required to mount the Inon
UWL-150AD Bayonet style wide-angle lens. The Wide-Angle
Adapter #9306.81 is required to mount the #6420 Ikelite W-20
Wide-Angle Lens and other manufacturers (67mm) screw
thread style wide-angle lenses.
These lenses can be secured onto the Wide-Angle Adapter
above or below water as they are designed to have water
between the front of the port and the accessory lens. Make sure
no air bubbles are trapped between the port and the accessory
lens. Any vignetting that occurs can be eliminated by zooming
the camera lens slightly. The camera’s built-in flash cannot be
used with wide angle
lenses. The front of the
lenses are so large they
block the camera’s flash.
To properly light subjects
when using a wide angle
lens an external strobe
should be used. Due to
the wide-angle of
coverage of these lenses,
the DS125 Substrobe is
recommended or two
DS51 Substrobes.
wide-angle lens
Wide-Angle Adapter
8 7
D Diiffffuusseerr aanndd D Deefflleeccttoorr ccoonntt..
A diffuser and deflector are
included with the housing. The
diffuser is white transparent
plastic. The deflector is also
white but is not transparent.
To install the diffuser or
deflector spread the port
clamp at the spring end
and slide over the lens port.
The white plastic should
be placed in front of the
camera flash. The port clamp
should be pushed back against the front of the housing.
D Diiffffuusseerr
The diffuser should be installed when using the camera’s built
in flash. When shooting with the camera’s built-in flash at
approximately 2 feet (0.6 m) or less, the lens port on the
housing may block a portion of the light from the camera’s
built-in flash, creating a shadow in the lower left of the photo.
If this occurs, zoom the lens slightly to eliminate the shadow.
(You can test this above water)
D Deefflleeccttoorr
The deflector should be installed when using an external strobe
such as the DS51 or DS125 Substrobe and EV Controller. The
deflector will redirect the camera’s flash to the EV Controller
which controls the external strobes output.
Diffuser/Deflector
material
Port Clamp
Spring
Spread to Install
This edge
against
housing
5
CChheecckkiinngg CCoonnttrroollss
Turn the camera on and operate each of the housing controls to
get a feel for using the camera in the housing. Take a few
pictures above water with the camera in the housing.
LLuubbrriiccaannttss
1. Ikelite provides silicone lubricant with the housing. We recommend
you use only Ikelite lubricant on Ikelite products as some other
brands may cause the o’ring to swell and not seal properly.
2. Use only enough lubricant to lightly cover control shafts and
o’rings. Wipe off any excess lubricant with a clean cloth.
Lubricant is not a sealant, it is used to reduce friction. Excessive
lubricant can collect sand and dirt which may interfere with
proper sealing.
CCAAU UTTIIO ON N
N Neevveerr uussee sspprraayy lluubbrriiccaannttss aass tthhee pprrooppeellllaanntt iinnggrreeddiieenntt ccaann
c caauussee tthhee ppllaassttiicc hhoouussiinngg ttoo ccrraacckk..
6
D Diiffffuusseerr & & D Deefflleeccttoorr IInnssttaallllaattiioonn
Housing shown with
Deflector installed.
Deflector