beautypg.com

Middleby Cooking Systems Group Gas Oven PS770 User Manual

Page 16

background image

16

II. NORMAL OPERATION - STEP-BY-STEP-

A. Daily Startup Procedure
1. Check that the circuit breaker/fused disconnect is in

the On position. Check that the window is closed.

The touch panel display should be lit.

2. Adjust the conveyor to the desired bake time.
3. Press the temperature button to display right and left

hand oven settings. Set temperatures as desired.

4. Press the ON button to activate the oven. The con-

veyor will not run, until the oven temperature has

reached the set points.

B. Daily Shutdown Procedure
1. Make certain there are no products left on the con-

veyor in the oven.

2. Press the ON square to turn the oven off.
3. Open the window to allow the oven to cool faster.
4. After the oven has cooled and the blowers have

turned off, the circuit breaker/fused disconnect may

be turned off.

Quick Reference – Touch Screen Controller
A. Main Screen
1. On/Off button - Used to turn oven On and Off.
2. Conveyor speed - Pressing on either the minutes

or seconds allows a new value to be input for the

conveyor speed. Split belt ovens have two inputs

(front and rear belts).

3. Oven temperature - Pressing on the set temperature

shifts the user to the oven temperature set point/

indicator screen.

4. Energy level indicators - Indicators to either side of

the screen indicate the energy input to that side of

the oven.

5. Message bar - Indicates various messages pertaining

to current oven conditions.

B. Oven Temperature/Set Point/Indicator Screen
1. Right actual temperature - Indicates current average

temperature of the right side of the oven.

2. Left actual temperature - Indicates current average

temperature of the left side of the oven.

NOTE: Right to Left temperature settings should not

exceed a differential of 20 °F.

3. Right Set point temperature - Pressing on this value

allows the user to adjust the set point for the right

side of the oven.

4. Left Set point temperature - Pressing on this value

allows the user to adjust the set point for the left side

of the oven.

5. Exit - Returns to the main screen.

C. Energy Mode Screen
1. Mode Two - Pressing this button allows the user to

set the amount of time that the oven allows before

shifting from energy mode 1 to energy mode 2. Set-

ting this value to zero disables this energy mode.

2. Mode Three - Pressing this button allows the user to

set the amount of time that the oven allows before

shifting from energy mode 2 to energy mode 3. Set-

ting this value to zero disables this energy mode.

3. Mode Four - Pressing this button allows the user to

set the amount of time that the oven allows before

shifting from energy mode 3 to oven off. Setting this

value to zero disables this energy mode.

Energy Modes
Energy Mode One - This mode is automatic, and starts

(bake time +1 minute) after the last product has entered

the oven. In this mode, the main oven blowers will lower

to 1500 RPM, while the oven maintains temperature and

belt speed.
Energy Mode Two - The oven lowers its set point by 100°

F, and stops the belt. Anytime that the oven is more than

10 degrees over its set point, the burners will completely

shut off, allowing the oven to cool and the burners are on

minimum flow. The main blowers will continue to run at

1500 RPM in this mode. Placing any article on the input

belt will cause normal operation of the oven to resume, and

bring the set point back to its original level. The belt will

resume operation once both sides of the oven are within

5° F of the set point.
Energy Mode Three - The oven will turn off completely and

shut off the circulation blowers once the oven temperature

has dropped below 200° F. Placing any article on the input

belt will cause normal operation of the oven to resume, and

bring the set point back to its original level. The belt will

resume operation once both sides of the over are within

5° F of the set point.
Energy Mode Four - This is a complete oven shut down.

Placing anything on the belt will NOT return the oven to

Operation. The ON button on the main screen has to be

pressed to restart the oven.