Marley Engineered Products Marley Utility Heater MCM1503A - Manual (Page 2)

FEATURES
• Tip-Over Switch - shuts heater off automatically if unit
tips over.
• Pilot Light - glows when heater is plugged in.
• Manual Reset Over-Temperature Safety Cutoff - auto-
matically turns heater off if overheating occurs.
Model MCM 1503A
This heater is provided with a grounded (3 blade) plug for use
on 110-120 volts AC.
CAUTION: The grounded plug must be used with a
grounded outlet. Do not use an adapter in a 2-slot wall
outlet unless the ground lug of the adapter is properly con-
nected to a known building ground. Failure to use heater
with properly grounded outlet or adapter could result in an
electric shock hazard. The adapter should not be used if a
3 slot grounded receptacle is available.
TO OPERATE
1. Plug the heater power cord directly into a standard
grounded 110-120 volt AC outlet. Always operate the
heater in the upright position with the rubber feet on the
floor.
CAUTION: Be sure plug fits tightly into outlet. A loose fit
will cause overheating and damage to the plug. Plug may
feel warm during normal usage.
2. Rotate heat selection knob to “LOW” (600W), “MED”
(900W) or HIGH (1500W) setting.
3. Rotate the “THERMOSTAT” knob clockwise (right)until
the knob stops. The heater should begin heating. At
“LOW” (600W) the fan will not operate. At “MED”
(900W) and “HIGH” (1500W) settings, the fan should
start to blow warm air.
4. Allow the heater to operate until the room temperature
reaches the desired level, then slowly rotate the
“THERMOSTAT” knob counter-clockwise (left) until the
heater cycles off. At this setting, the heater will cycle on
and off automatically to maintain this comfort level.
NOTE: Do not force knob beyond its normal stop
position. It may be necessary to make minor
adjustments to the thermostat to maintain the
desired comfort level. Clockwise movement will
increase the room temperature. Counter-clockwise
movement will decrease room temperature.
5. To conserve energy, the heater may be operated at a
lower wattage by placing the heat selection knob at the
“LOW” (600W) or MED (900W) settings.
6. When heater is not needed, rotate control knob to the
“OFF” position, remove the plug from outlet, and move
heater to safe place for storage.
CLEANING & CARE
Your heater is designed for trouble-free operation with little
maintenance. However, routine cleaning is recommended
as follows:
1. Before attempting to clean heater, turn heater to “OFF”
position and remove plug from outlet.
2. Using damp cloth, wipe dust and dirt from heater to
cabinet. Do not use waxes as they may discolor.
3. When heater is not to be used for an extended time,
turn to “OFF” position, unplug from outlet and place
heater in safe place, such as a box, to prevent possible
damage.
TO RESET OVER-TEMPERATURE CONTROL
This heater is equipped with a built-in over-temperature
safety switch that will cycle the heater off if the heater
overheats. After heater is allowed to cool and the condition
that caused the overheating is corrected, using a small
straight object, such as a pencil, push in button located
inside small hole on side of heater marked “RESET”.
LIMITED WARRANTY
All products manufactured by Marley Engineered Products are warranted against defects in workmanship and materials for two years from date of pur-
chase. This warranty does not apply to damage from accident, misuse, or alteration; nor where the connected voltage is more than 5% above the
nameplate voltage; not to equipment improperly installed or wired or maintained in violation of the product’s installation instructions. All claims for war-
ranty work must be accompanied by proof of the date of installation.
The customer shall be responsible for all costs incurred in the removal or reinstallation of products, including labor costs, and shipping costs incurred
to return products to Marley Engineered Products Service Center. Within the limitations of this warranty, inoperative units should be returned to the
nearest Marley authorized service center or the Marley Engineered Products Service Center, and we will repair or replace, at our option, at no charge
to you with return freight paid by Marley.
It is agreed that such repair or replacement is the exclusive remedy available from Marley Engineered Products.
THE ABOVE WARRANTIES ARE IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED, AND ALL IMPLIED WARRANTIES OF MER-
CHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE WHICH EXCEED THE AFORESAID EXPRESSED WARRANTIES ARE HEREBY
DISCLAIMED AND EXCLUDED FROM THIS AGREEMENT. MARLEY ENGINEERED PRODUCTS SHALL NOT BE LIABLE FOR CONSEQUENTIAL
DAMAGES ARISING WITH RESPECT TO THE PRODUCT, WHETHER BASED UPON NEGLIGENCE, TORT, STRICT LIABILITY, OR CONTRACT.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above exclusion or limitation may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
For the address of your nearest authorized service center, contact Marley Engineered Products in Bennettsville, SC, at 1-800-642-4328. Merchandise
returned to the factory must be accompanied by a return authorization and service identification tag, both available from Marley Engineered Products.
When requesting return authorization, include all catalog numbers shown on the products.
SAVE THESE IMPORTANT INSTRUCTIONS
NEED TECHNICAL OR WARRANTY ASSISTANCE?
PLEASE CALL TOLL-FREE 1-800-642-HEAT.
PPD 029
6/99
5200-2455-000
2
SPX Corporation
470 Beauty Spot Rd. East
Bennettsville, SC 29512 USA