Meyer Sound UPA-2P - Manual (Page 2)

AC Input 100-240V ~
50-60Hz 4A MAX
24VFan - +
Loop Input On / Temp.
Limit
Earth /
Chassis
Case
220k Ω
GND Circuit 1
2
3 1
2
3 Looping Audio Input
Push
Network Service Wink Reset Activity
R e m o t e M o n i t o r S y s t e m
!
Meyer Sound, Berkeley, CA. USA
CAUTION : See instruction manual
ATTENTION : Voir le cahier d'instruction
A c o u s t i c a l
(each loudspeaker)
C o v e r a g e
C r o s s o v e r
T r a n s d u c e r s
S t a n d a r d A u d i o
I n p u t M o d u l e *
A m p l i f i e r s
A C P o w e r
P h y s i c a l
N o t e s
PHYSICAL DIMENSIONS
UPA-1P & 2P SPECIFICATIONS
Operating Frequency Range 2
Free Field
Half-Space 3
Phase Response 4
Maximum SPL
5
UPA-1P (-6 dB points)
UPA-2P (-6 dB points)
UPA-1P
UPA-2P
Low Frequency
High Frequency
Type
Connector
Impedance
XLR Wiring
RF Filter
Common Mode Rejection Ratio
Type
Burst capability 6
THD, IM, TIM
Connector
Automatic voltage selection
Idle RMS Current
Max Continuous RMS Current (>10 sec)
Max Burst RMS Current (<1 sec)
Max Peak Current During Burst
Soft-Current Turn-on
Dimensions
Weight
Enclosure
Finish
Protective Grill
Rigging
60 Hz - 18 kHz
100 Hz - 16 kHz ± 3dB; -6 dB at 77 Hz and 18 kHz
77 Hz - 16 kHz ± 3dB; -6 dB at 66 Hz and 18 kHz
± 35° 600 Hz - 16 kHz; + 90° at 250 Hz
133 dB SPL
100° H; 40° V
45° H; 45° V
1200 Hz
1000 Hz
12" cone driver
3" diaphragm compression driver
Differential balanced input circuit
Female XLR; male XLR loop
10 kΩ differential balanced (between pins 2 and 3)
Pin 1: chassis; Pin 2: + signal; Pin 3: - signal
Common Mode: 425 kHz low-pass; Differential Mode: 142 kHz low-pass
> 80 dB (50 Hz - 1 kHz); typically 90 dB
Complementary power MOSFET output stages (class AB/bridged)
350 Wrms/channel
< .02 %
PowerCon locking AC connector
80-264 VAC continuous; 47/63 Hz
4
@115 V: 0.25Arms @230V: 0.13Arms @100V: 0.3Arms
@115 V: 2.8Arms @230V: 1.4Arms @100V: 3.2Arms
@115 V: 3.2Arms @230V: 1.6Arms @100V: 3.7Arms
@115 V: 5.0Apk @230V: 2.5Apk @100V: 5.8Apk
Inrush current <15A@115V
14.5" W x 22.4" H x 14.5" D
77 lbs (35 kg)
5 / 8 ” plywood
Black textured
Hex perforated steel grill, charcoal grey foam
Four aircraft pan fittings (two on top, two on bottom). Working load
is 600 lb (273 kg), based on a 5:1 safety factor.
1
1. Measurements are taken at 3m on-axis, 1 / 3 octave, unless otherwise stated.
2. Response depends on loading conditions and room acoustics.
3. Measured with a single boundary, 1 m from rear of cabinet.
4. Phase variation from pure delay.
5. Measured at 1 m, with pink noise or music.
6. Nominal 8Ω resistive load, pink noise, 100v peak.
* Refer to UPA series Q+A for input module options.
ALL UNITS IN INCHES
Meyer Sound Laboratories, Inc.
2832 San Pablo Avenue
Berkeley, CA 94702
tel: 510.486.1166
fax: 510.486.8356
e-mail: [email protected]
http://www.meyersound.com
U U
L L
C C
U U
L L
® ®
LISTED
3K59
COMMERCIAL
AUDIO SYSTEM
Meyer Sound Laboratories
has devoted itself to
designing, manufacturing,
and refining components
that deliver superb sonic
reproduction. Every part of
every component is
designed and built to
exacting specifications
and undergoes rigorous,
comprehensive testing
in the laboratories.
Research remains an
integral, driving force
behind all production.
Meyer strives for sound
quality that is predictable
and neutral over an
extended lifetime and
across an extended range.
Made by Meyer Sound, Berkeley, CA, USA
European Office:
Meyer Sound Germany
GmbH
Carl Zeiss Strasse 13
56751 Polch, Germany
© 1997 Meyer Sound Laboratories, Inc.
All rights reserved
UPA1P&2P - 04.054.017.01D
14.3
30 °
14.5
12.8
7.7
2.6
7.5
22.4
AC Input 100-240V ~ 50-60Hz 4A MAX
24VFan - + Loop Input On / Temp.
Limit Earth /
Chassis Case 220k Ω Ω GND Circuit 1 1 2 2 3 3 1 1 2 2 3 3 Looping Audio Input Push
Network Service Wink Reset Activity R e m o t e M o n i t o r S y s t e m ! Meyer Sound, Berkeley, CA. USA CAUTION: See instruction manual ATTENTION: Voir le cahier d'instruction
UPA-1P UPA-2P