Murphy Selectronic Micro-Controller Series 1500 - Manual (Page 3)

Relays, Timers, and Sensor Input Class Ordering Your Configuration
Sensor Input Specify Class Specify Function Default Nomenclature User Specified Nomenclature
Example: Class B2 SD Compressor Oil Pressure Compressor #1 Oil Pressure
Input 1 ____________ _________________ Compressor Oil Pressure ________________________
Input 2 ____________ _________________ Compressor Oil Level ________________________
Input 3 ____________ _________________ Lubrication No-Flow ________________________
Input 4 ____________ _________________ Low Suction Pressure ________________________
Input 5 ____________ _________________ Interstage Pressure #1 ________________________
Input 6 ____________ _________________ Interstage Pressure #2 ________________________
Input 7 ____________ _________________ Interstage Pressure #3 ________________________
Input 8 ____________ _________________ Discharge Pressure ________________________
Input 9 ____________ _________________ Discharge Temperature #1 ________________________
Input 10 ____________ _________________ Discharge Temperature #2 ________________________
Input 11 ____________ _________________ Discharge Temperature #3 ________________________
Input 12 ____________ _________________ Discharge Temperature #4 ________________________
Input 13 ____________ _________________ Suction Liquid Level ________________________
Input 14 ____________ _________________ Interstage Liquid Level #1 ________________________
Input 15 ____________ _________________ Interstage Liquid Level #2 ________________________
Input 16 ____________ _________________ Interstage Liquid Level #3 ________________________
Input 17 ____________ _________________ Inlet Scrubber Liquid Level ________________________
Input 18 ____________ _________________ Engine Oil Pressure ________________________
Input 19 ____________ _________________ Engine Oil Level ________________________
Input 20 ____________ _________________ Engine Oil Vibration ________________________
Input 21 ____________ _________________ Engine Jacket Water Temp. ________________________
Input 22 ____________ _________________ Engine Jacket Water Level ________________________
Input 23 ____________ _________________ Engine Jacket Water Press. ________________________
Input 24 ____________ _________________ Engine Vacuum Right Bank ________________________
Input 25 ____________ _________________ Engine Vacuum Left Bank ________________________
Input 26 ____________ _________________ Compressor Vibration ________________________
Input 27 ____________ _________________ Cooler Vibration ________________________
Input 28 ____________ _________________ Cooler Water Level ________________________
Input 29 ____________ _________________ Auxiliary Pump Shutdown ________________________
Input 30 ____________ _________________ Emergency Shutdown ________________________
Input 31 ____________ _________________ PLC Shutdown ________________________
Input 32 ____________ _________________ Prelube Permissive ________________________
Use the listings below to specify sensor input Class, Function and Nomenclature; the S1500 sensor inputs are factory-configured as follows:
Class A: Armed at all times for alarm or shutdown (specify). Class P: Locked out by the Compressor Load lockout timer.
Class B1: Locked out by first lockout timer (First Start/Run timer). ESD: Overrides the Test lockout timer (for Remote/Emergency Stop input).
Class B2: Locked out by second lockout timer (Second Start/Run timer). SD: S1500 System Shutdown Function.
Class C: Armed after fault condition has been cleared for 2 seconds. AL: Alarm Relay Function (no shutdown).
Select your Relay Logic Mode (see page 4):
MODE No. ____________________
Select your Timing and range; (default values)
TACHOMETER
Pulses/Rev.: _____________________ (60)
Crank Disconnect: _______________ (100)
Underspeed: ____________________ (150)
Overspeed: _____________________ (400)
TIMERS
Prelube: ___________________ (0:30)
Run Delay: _________________ (0:30)
Class B1: ___________________ (1:00)
Class B2: ___________________ (1:00)
Load Delay: _________________ (1:00)
Process Delay: _______________ (1:30)
Idle/Cooldown: _______________(5:00)
Ignition Ground: _______________ (0:10)
Postlube: ______________________ (0:30)
CRANKING
Attempts: ______________________ (5)
Crank Period: __________________ (0:15)
Rest Period: ____________________ (0:15)
DISCONTINUED