Marantz CR401 - Manual (Page 19)

15
ENGLISH
TUNER OPERATION
LISTENING TO FM/AM
7 FM Auto preset memory
1. Press the POWER ON/STANDBY switch q or
button z to turn on the power.
2. Watching the display, press the INPUT button
i or . or FM button ⁄9 to select the FM band.
3. Press the AUTO TUNE button ⁄4 .
4. Press the ENTER button b .
• The unit automatically begins searching for
FM broadcast stations.
• When the first FM broadcast station is found,
that station is stored in the preset memory at
channel A1.
• Subsequent stations are automatically stored
in order at preset channels A1 to A10, B1 to
B10, C1 to C10, D1 to D10 for a maximum of
40 stations.
• Channel A1 is tuned in after the auto preset
memory operation is completed.
Notes
• If an FM station cannot be preset automatically
due to poor reception, use the “Manual tuning”
operation to tune in the station, then preset it
using the manual “Preset memory” operation.
• To interrupt this function, press the POWER
ON/STANDBY switch q or button z .
• Perform this operation from the remote control
unit.
7 Default value
7 Auto tuning (FM/AM)
1. Press the POWER ON/STANDBY switch q or
button z to turn on the power.
2. Watching the display, press the INPUT button
i or . or FM button ⁄9 or AM button ¤1 to
select the desired band (AM or FM).
3. Press the MENU button u or n to select
menu.
4. Either turn the Easy JOG 4 / ¢ knob !5 or
press the 5 or ∞ button c to select “ Search
Mode ”.
5. Press the Easy JOG 4 / ¢ knob !5 or
ENTER button b to set search mode.
6. Either turn the Easy JOG 4 / ¢ knob !5 or
press the 5 or ∞ button c to select “ Auto ”.
7. Press the Easy JOG 4 / ¢ knob !5 or
ENTER button b to set the auto tuning mode.
Auto tuner presets
A1 ~ A10
87.5 / 89.1 / 98.1 / 108 / 90.1 / 90.1 /
90.1 / 90.1 / 90.1 / 90.1 MHz
B1 ~ B10
522 / 603 / 999 / 1404 / 1611 kHz,
90.1 / 90.1 / 90.1 / 90.1 / 90.1 MHz
C1 ~ C10 90.1 MHz
D1 ~ D10 90.1 MHz
8. Either turn the Easy JOG 4 / ¢ knob !5 or
press the 1 button ⁄1 or ¡ button ⁄2 .
• Automatic searching begins, then stops when
a station tuned in.
Notes
• When in the auto tuning mode on the FM band,
the display on the panel when the stereo
broadcast is tuned in. At open frequencies, the
noise is muted and the
tuned off.
• If the signal is weak, if may be difficult to tune
into the station in stereo. In such a case, press
the
MODE button , on the remote control. FM
stereo broadcasts are received in monaural and
the
is not illuminated. To return to stereo
mode, press the MODE button , on the remote
control again.
• If tuning does not stop at the desired station.
Use “Manual tuning” operation.
7 Manual tuning (FM/AM)
1. Press the POWER ON/STANDBY switch q or
button z to turn on the power.
2. Watching the display, press the INPUT button
i or . or FM button ⁄9 or AM button ¤1 to
select the desired band (AM or FM).
3. Press the MENU button u or n to select
menu.
4. Either turn the Easy JOG 4 / ¢ knob !5 or
press the 5 or ∞ button c to select “ Search
Mode ”.
5. Press the Easy JOG 4 / ¢ knob !5 or
ENTER button b to set search mode.
6. Either turn the Easy JOG 4 / ¢ knob !5 or
press the 5 or ∞ button c to select “ Manual ”.
7. Press the Easy JOG 4 / ¢ knob !5 or ENTER
button b to set the manual tuning mode.
8. Either turn the Easy JOG 4 / ¢ knob !5 or
press the 1 button ⁄1 or ¡ button ⁄2 to tune
in the desired station.
• The frequency changes continuously when
the 1 button ⁄1 or ¡ button ⁄2 on the
remote control unit is held in.
STANDBY STANDBY PHONES PHONES POWER ON / STANDBY POWER ON / STANDBY
CD RECEIVER CR401 CD RECEIVER CR401
PUSH TO ENTER PUSH TO ENTER VOLUME VOLUME
TREBLE TREBLE BASS BASS
INPUT INPUT MENU MENU DIRECT DIRECT
i
q
u !5
MEMO
AUTO TUNE SLEEP SHIFT DIRECT
AM FM DAB
--/---
MUTE
DISPLAY
VOL
INPUT
DIMM
VOL
10/0
9
8 7
6
5 4
3
2 1
INPUT
MODE
TUNING PRESET
ENTER
CLOCK CALL
MENU
CLEAR
TIMER
REPEAT
REMOTE CONTROLLER RC601CR REMOTE CONTROLLER RC601CR REMOTE CONTROLLER RC601CR
n
⁄4
¤1
⁄9
.
z
b
,
⁄2
⁄1
c
STEREO receive mode
TUNED mode
AUTO TUNING mode