Mica specifications – Meyer Sound M SERIES User Manual
Page 11
0
4
.
1
4
]
m
m
2
5
0
1
[
8
8
.
3
4
]
m
m
5
1
1
1
[
8
7
.
7
1
]
m
m
2
5
4
[
7
3
.
3
1
]
m
m
0
4
3
[
8
5
.
1
1
]
m
m
4
9
2
[
1. Recommended maximum operat-
ing frequency range. Response
depends on loading conditions and
room acoustics.
2. Free field, measured with 1/3-
octave frequency resolution at 4
meters.
3. Measured with music referred to 1
meter.
4. Power handling is measured under
AES standard conditions: both
transducers driven continuously for
two hours with band-limited noise
signal having a 6 dB peak-average
ratio.
5. Peak power handling is measured
with both transducers driven for
100 milliseconds with pink noise
signal having a 12 dB peak-aver-
age ratio.
Operating Frequency Range
1
Frequency Response
2
Maximum Peak SPL
3
Horizontal
Vertical
Low/Low-Mid Frequency
High Frequency
6
Connector
Type
Output Power
7
Total Output
8
Connector
Automatic Voltage Selection
Turn-on and Turn-off Points
Max Long-Term Continuous Current (>10 sec)
9
Dimensions
Weight
Enclosure
Finish
Protective Grille
Rigging
60 Hz - 18 kHz
75 Hz - 17 kHz ±4 dB
138 dB
100°
Varies, depending on array length and configuration
Two high-power 10" cone drivers with neodymium magnets
Nominal impedance: 4
Ω
Voice coil size: 2"
Power handling capability: 1200 W (AES)
4
; 1800 W peak
5
Two 3" compression drivers
Nominal impedance: 8
Ω
V
oice coil size: 3"
Diaphragm size: 3"
Exit size: 1.2"
Power handling capability: 360 W (AES)
4
; 720 W peak
5
Female XLR input with male XLR loop output or VEAM all-in-one
connector (integrates AC, audio, and network)
Four-channel complementary MOSFET output stages (class AB/H)
3020 W (four channels; 2 x 950 W, 2 x 560 W)
6000 W peak
250 V AC NEMA L6-20 twistlock, IEC-309 male, PowerCon, or VEAM
Automatic, two ranges, each with high-low voltage tap (uninterrupted)
85 V AC - 134 V AC; 165 V AC - 264 V AC
8.7 A rms (115 V AC); 4.3 A rms (230 V AC); 10.0 A rms (100 V AC)
Equipped with two-conductor twisted-pair network, reporting all
operating parameters of amplifiers to system operator’s host computer
41.40 w x 13.37 h x 17.78 d
(1052 mm x 340 mm x 452 mm)
150 lbs (68.04 kg)
Premium birch plywood
Black textured
Powder-coated, hex-stamped steel, black mesh
QuickFly rigging with four captive AlignaLinks in the bottom
corners of two aluminum and steel end frames, secured with
quick-release pins
ACOUSTICAL
COVERAGE
TRANSDUCERS
AUDIO INPUT
AMPLIFIER
AC POWER
RMS NETWORK
PHYSICAL
MICA SPECIFICATIONS
0
4
.
1
4
]
m
m
2
5
0
1
[
8
8
.
3
4
]
m
m
5
1
1
1
[
8
7
.
7
1
]
m
m
2
5
4
[
7
3
.
3
1
]
m
m
0
4
3
[
8
5
.
1
1
]
m
m
4
9
2
[
6. The two drivers are coupled to a
100-degree-horizontal constant-
directivity horn through a propri-
etary acoustical combining manifold
(REM).
7. Amplifier wattage rating based on
the maximum unclipped burst sine-
wave rms voltage that the amplifier
will produce for at least 0.5 seconds
into the nominal load impedance.
8. Peak power based on the maximum
unclipped peak voltage that the
amplifier will produce for at least
100 milliseconds into the nominal
load impedance.
9. AC power cabling must be of suf-
ficient gauge so that under burst
current rms conditions, cable trans-
mission losses do not drop voltage
below specified operating range at
the speaker.
0
4
.
1
4
]
m
m
2
5
0
1
[
8
8
.
3
4
]
m
m
5
1
1
1
[
8
7
.
7
1
]
m
m
2
5
4
[
7
3
.
3
1
]
m
m
0
4
3
[
8
5
.
1
1
]
m
m
4
9
2
[
compact high-power curvilinear array loudspeaker