Marantz SR5000 - Manual (Page 12)

EN
G
LI
S
H
LEARNING OF OTHER MAKER'S REMOTE CONTROL CODE
This remote control unit can learn, or program in itself, the remote control
code of any function preset under any button of the remote control unit of
any system component, except for the MAIN POWER switch of the
SR5000. The functions of the components that can be controlled through
the D-BUS (RC-5) need not be learned, but the functions of other components
must be learned before they can be controlled from the RC5000SR remote
control unit. To let the RC5000SR learn the remote control code of a
function of a component, follow the learning procedure described below.
1. Set the mode switch to LEARN.
2. Select the component with the codes to be learned, by pressing one of
the input selector buttons.
For example, when the CD button is pressed, most of the buttons on
the remote handset get ready to learn the CD control codes.
3. On the RC5000SR, press the button corresponding to the function to
be learned. For example, if the function to be learned is playback, press
the PLAY (
) button on the remote control unit. The Learn indicator
will light up.
4. Place the remote control unit of the component with the function to be
learned at a distance of about 20 cm (8 inches) from the RC5000SR, so
that the head (transmitting side) of the former remote control unit
points the head of the RC5000SR.
5. On the remote control unit of the component, press and hold the button
of the function to be learned, until the learning indicator of the
RC5000SR starts to blink then goes off. The learning operation is
complete when the indicator is extinguished.
6. Set the mode switch to USER.
7. Let the RC5000SR learn other codes by repeating the steps above for
each code.
Note:
When the system mode switch is in the USER position, the buttons
which have not learned any function output the D-BUS (RC-5) codes
when they are pressed. In the RC-5 (D-BUS) position, all buttons output
the D-BUS (RC-5) codes.
RECALLING THE PRESET FUNCTION
Even after a button has learned the remote control code of a function, its
originally preset, D-BUS (RC-5) code can be recalled any time by following
the procedure below.
1. Set the mode switch to LEARN.
2. Press the MAIN POWER OFF button and the button which has learned
a function simultaneously.
3. Set the mode switch to USER.
Learning button indications
Although the learning buttons can be used to operate various components,
the indications printed above the buttons are Marantz D-BUS (RC-5) preset
code indications. To make it easier to remember which buttons perform
which operations, therefore, we recommend that you program operations
into buttons having the same or similar indications.
There are some situations where programming is not possible.
In the following instances, both the TX and LEARN LEDs blink to indicate
that programming cannot be carried out.
1. When the remote control unit’s memory is full.
2. When you attempt to program a command from a remote control unit
using a different signal transmission format.
CLEARING ALL OF THE LEARNED CODES
Use the following procedure to reset all of the buttons which have learned
remote control codes and make them possible to output RC-5 preset
codes.
1. Set the mode switch to LEARN.
2. Hold down the main POWER ON and OFF buttons simultaneously for
more than 3 seconds.
3. Set the mode switch to USER.
11
SURROUND LEVEL button
When DTS mode
Adjust the center level with CENTER UP/DOWN button : Changeable
range is
10dB
Adjust the Surround R channel level , and after 2 seconds, adjust the
surround L channel with SURR.UP/DOWN button. Changeable range is
15dB
Adjust the Sub woofer level (when sub woofer is ON) with SUB. WOOFER
UP/DOWN button. Changeable range is
10dB
When Dolby Digital mode
Adjust the center level with CENTER UP/DOWN button : Changeable
range is
10dB
Adjust the Surround channel level , and after 2 seconds, adjust the
surround L channel with SURR.UP/DOWN button. Changeable range is
15dB
Adjust the Sub woofer level (when sub woofer is ON) with SUB. WOOFER
UP/DOWN button. Changeable range is
10dB
When Dolby Pro logic mode
Adjust the center level with CENTER UP/DOWN button : Changeable
range is
10dB
Adjust the Surround channel level. Changeable range is 15dB
Adjust the Sub woofer level (when sub woofer is ON) with SUB.WOOFER
UP/DOWN button. Changeable range is
10dB
When Other surround mode
Adjust the Surround channel leve. Changeable range is
15dB
Adjust the Sub woofer level (when sub woofer is ON) with SUB.WOOFER
UP/DOWN button.
Changeable range is
10dB
When STEREO mode: Does not operate.
⁄3 DIGITAL SELECT buttons
RF button : does not apply in SR5000.
OPT button: Press to select the optical input when digital equipment
(CD, LD, DVD) is selected as the function.
COAX. button: Press to select the coaxial input when digital equipment
(CD, LD, DVD) is selected as the function. Pressing COAX. again
changes the input as follows
Coaxial-1 / CoaxiaI-2
⁄4 MID NIGHT button
When Dolby Digital and Dolby Digital Down mix mode, the source with
large dynamic range is compressed.
OTHER button
Please see the other equipment’s user guide of Marantz models.