Fussion 3000 specifications – MACKIE 3000 User Manual

Page 11

FUSSION 3000 SPECIFICATIONS

Line Input Power

US:

115V, 60Hz

Recommended Amperage Service:

20A recommended

AC Connector:

3-pin Twistlock
250VAC, 20A male

Europe:

230V, 50Hz

Recommended Amperage Service:

16A recommended

AC Connector:

3-pin IEC
250VAC, 16A male

In-rush Current Protection:

Transistor-based

Safety Features

RMS Limiting:

Monitoring and limiting
of continuous RMS
output of amplifiers

Thermal Protection:

Input stage shutdown,
auto-reset

Physical Properties

Enclosure:

Trapezoidal, 15º side
angles, 18mm multi-
layered birch

Hanging Inserts:

4 points on top

Rigging Inserts:

2 points, 1 each side
ATM MEGS
1 pull-back clip, bottom

Handles:

4 ea. aluminum/rubber
grips

Height:

41.9˝ (1064mm)

Front Width:

24.7˝ (628mm)

Rear Width:

13.9˝ (352mm)

Depth:

22.6˝ (575mm)

Weight:

246 lbs. (112kg)

Options

Active Subwoofer System:

FUSSION 1800SA/1800S

Flyware:

ATM MEGS compatible

Disclaimer

Since we are always striving to make our

products better by incorporating new and improved
materials, components, and manufacturing methods,
we reserve the right to change these specifications at
any time without notice.

“Mackie,” the “Running Man” figure, and

“FUSSION” are trademarks or registered trade-
marks of Mackie Designs Inc.

All other brand names mentioned are trade-

marks or registered trademarks of their respective
holders, and are hereby acknowledged.

System Acoustic

Frequency Range (–10 dB): 45Hz-20kHz
Frequency Response (–3 dB): 55Hz-18kHz
Horizontal Coverage (–6 dB): 80º averaged 2kHz-10kHz
Vertical Coverage (–6 dB): 70º averaged 2kHz-10kHz
Directivity Factor; DI (Q): 10.19 (10.46) averaged

2kHz to 10kHz

Maximum SPL (long term): 130 dB @ 1m
Maximum SPL (peak):

133 dB @ 1m

Maximum SPL (long term—High Pass ON): 132 dB
Maximum SPL (peak—High Pass ON):

135 dB

Crossover Points:

500Hz, 2500Hz

Dynamic Range:

> 110 dB

Phase Response:

± 35º from 500Hz-10kHz

Transducers

Low-Frequency Transducers—Four Each

Cone Diameter:

12˝ (300mm)

Voice Coil Diameter:

3˝ (75mm)

Nominal Impedance:

8 ohms each

Power Handling:

350 watts rms (long term)

Mid-Frequency Transducer

Cone Diameter:

8˝ (200mm)

Voice Coil Diameter:

2˝ (50mm)

Nominal Impedance:

8 ohms

Power Handling:

150 watts rms (long term)

High-Frequency Transducer

Diaphragm Diameter: 3˝ (75mm)
Throat Exit Diameter: 1.4˝ (35.6mm)
Nominal Impedance:

8 ohms

Power Handling:

75 watts rms (long term)

Diaphragm Material:

Titanium

Power Amplifiers

Low-Frequency Power Amplifier

Rated Power:

1000W continuous @ 8

Ω

1500W peak @ 8

Ω

Rated THD:

< 0.03%

Mid-Frequency Power Amplifier

Rated Power:

200W continuous @ 8

Ω

300W peak @ 8

Ω

Rated THD:

< 0.03%

High-Frequency Power Amplifier

Rated Power:

100W continuous @ 8

Ω

150W peak @ 8

Ω

Rated THD:

< 0.03%

Audio Input/Output/Controls

Input Type:

Balanced differential

Input Impedance:

50k ohms

Sub-Out:

85Hz low-pass output

with protection and active monitoring
for FUSSION 1800S/1800SA active
subwoofer system

Fill-Out:

85Hz high-pass output

Fill-Out Level:

0 dB to –30 dB

Fill-Out Phase Control: 0º/180º
High-Pass Switch:

85Hz high-pass to LF
driver

Power handling for transducers is based on an AES long term power

testing standard conducted for 100 hours full power, free air.