Morphy Richards 40652 - Manual (Page 5)

55
FILLING A A
11 Make sure that the iron is not
plugged in and then set the
variable steam control ‹ ‹ to the
‘0’ position before filling the iron
with water.
22 Open the fill cap and pour water
through the filling hole › › into
the water tank · · , using the
beaker provided, one beaker full
of water fills the tank (400ml). A A
After filling, replace the fill cap.
In hard water areas, the use of
distilled or demineralised water
is recommended.
Never use battery topping up
fluid or water containing any
substances like starch, or sugar,
or defrosted water from a
refrigerator.
33 Always pour out the remaining
water after use.
W Waarrnniinngg:: W Whheenn ffiilllliinngg yyoouurr iirroonn
w wiitthh ttaapp w waatteerr,, aallw waayyss uussee tthhee
bbeeaakkeerr pprroovviiddeedd.. N Neevveerr ffiillll
ddiirreeccttllyy uunnddeerr tthhee ttaapp..
Temperature
control
B B
Plug in the iron and switch on.
The ‘power on’ indicator lights
„ „ , situated in the back cover,
will illuminate. Set the
temperature control dial B B to
the temperature required, but
don’t start ironing immediately. If
you wait a few minutes, the iron
will stabilise at the required
setting.
Your Morphy Richards iron is
fitted with an indicator light ‡ ‡
which will go on and off while
you are ironing. This is perfectly
normal as it shows that the iron
is maintaining the heat setting
you have chosen.
IItt iiss aallw waayyss aa ggoooodd iiddeeaa ttoo
bbeeggiinn w wiitthh ccooooll ffaabbrriiccss aanndd
w woorrkk uupp ttoo hhiigghheerr sseettttiinnggss..
A Ann iirroonn hheeaattss uupp qquuiicckkeerr tthhaann
iitt ccoooollss ddoow wnn ssoo yyoouu’’llll ssaavvee
ttiim mee aanndd eelleeccttrriicciittyy..
FEATURES OF YOUR
IRON
Temperature
indicator light
The indicator light under the
control knob shows that the iron
is warming up. When the
required temperature is reached,
the light will go out and will
cycle on-off during operation.
Dry ironing
You can use your iron as a dry
iron only. Make sure the variable
steam control ‹ ‹ is set to the ‘0’
symbol.
Any temperature setting may be
used depending on the garment.
The spray feature may be used
provided there is water in the
tank (see ‘Filling’ section). You
do not need to put any water in
the tank when dry ironing only.
Spray
C C
Press the spray button ¤ ¤ and
aim the spray of water at
stubborn creases. You can do
this whilst dry ironing, providing
there is water in the tank. When
using the water spray it may be
necessary to push the button a
few times to get the spray pump
primed.
Variable steam
D D
Fill the iron with water as
described in ‘Filling’, and insert
the plug into the electrical
socket.
The steam output can be varied
from low to high by sliding the
variable steam control D D . When
using the iron at the bottom of
the steam range, the steam
output should be adjusted to the
lowest setting.
The steam facility should only
be used on garments which are
suitable for ironing within the
steam band.
Steam uses additional energy.
To save energy, only use steam
when necessary.
A
Min
M
ax
Silk
Nylon Wool
C
ott
on Linen
B B
C C
D D
lower
steam
2 dot
higher
steam
3 dot
40652 rev1 23/4/08 17:52 Page 5