MTD Y26SS - Manual (Page 4)

4
Cutting
Attachment
Shield
Fuel
Cap
Throttle
Control
J-Handle
Cutting
Attachment
Shaft Grip
Primer
Bulb
Oil Fill Plug / Dipstick
Choke
Lever
Spark
Plug
Shaft
Housing
Starter Rope Grip
Line
Cutting
Blade
Spark
Plug
Muffler
Muffler Guard
Spark Arrestor
On/Off Stop
Control
KNOW YOUR UNIT
Air Filter
Cover
OIL AND FUEL INFORMATION
ASSEMBLY INSTRUCTIONS
Definition of Blended Fuels
Today's fuels are often a blend of gasoline and oxygenates
such as ethanol, methanol or MTBE (ether). Alcohol-blended
fuel absorbs water. As little as 1% water in the fuel can make
fuel and oil separate or form acids when stored. Use fresh fuel
(less than 60 days old), when using alcohol-blended fuel.
Using Blended Fuels
If you choose to use a blended fuel, or its use is unavoidable,
follow recommended precautions:
• Always use fresh unleaded gasoline
• Use the fuel additive STA-BIL® or an equivalent
• Drain tank and run the engine dry before storing unit
Using Fuel Additives
The use of fuel additives, such as STA-BIL® Gas Stabilizer or
an equivalent, will inhibit corrosion and minimize the formation
of gum deposits. Using a fuel additive can keep fuel from
forming harmful deposits in the carburetor for up to six (6)
months. Add 0.8 oz. (23 ml.) of fuel additive per gallon of fuel
according to the instructions on the container. NEVER add fuel
additives directly to the unit's gas tank.
FUELING THE UNIT
1. Remove the fuel cap (Fig. 4).
2. Place the gas container’s spout into the fill hole on the fuel
tank (Fig. 4) and fill the tank.
NOTE: Do not overfill the tank.
3. Wipe up any gasoline that may have spilled.
4. Reinstall the fuel cap.
5. Move the unit at least 30 ft. (9.1 m) from the fueling source
and site before starting the engine.
NOTE: Dispose of the old gasoline in accordance to Federal,
State and Local regulations.
WARNING: Add fuel in a clean, well ventilated
outdoor area. Wipe up any spilled fuel immediately.
Avoid creating a source of ignition for spilt fuel. Do
not start the engine until fuel vapors dissipate.
WARNING: Gasoline is extremely flammable.
Ignited vapors may explode. Always stop the engine
and allow it to cool before filling the fuel tank. Do not
smoke while filling the tank. Keep sparks and open
flames at a distance from the area.
WARNING: Remove fuel cap slowly to avoid injury
from fuel spray. Never operate the unit without the
fuel cap securely in place.
Fig. 4
Fuel Cap
Fuel Tank
Gas Can Spout
Unleaded
Gasoline
INSTALL AND ADJUST THE J-HANDLE
The Y26SS is equipped with a J-handle.
1.
Place the J-handle between the top and middle clamp
pieces (Fig. 5).
2. While holding
the 3 pieces
together, install
the 4 screws
through the top
clamp and into
middle clamp.
NOTE: The holes
in the top and
middle clamp
will line up
only when
assembled correctly.
3. Place the clamps and the J-handle over the shaft housing
and onto the bottom clamp.
4. Hold each hex nut in the bottom clamp recess with a
finger. Start screws with a large Phillips screwdriver. Do
not tighten until you make the handle adjustment.
5. Slide the J-handle in or out until the arrow/white line on the
decal touches the clamp assembly (Fig. 5). You must first
loosen the screws if the handle is pre-installed.
6. While holding the unit in the operating position (Fig. 14),
position the J-handle to the location that provides you the
best grip.
7. Tighten the clamp screws evenly until tight.
Screws (4)
Top
Clamp
Middle Clamp
Bottom Clamp
Nuts
Fig. 5
Decal
J-Handle
Top Clamp