METRObility Optical Systems R104-11 - Manual (Page 8)

8 Installation Guide
AN indicates that auto-negotiation is enabled.
+ indicates the switch is enabled (OPEN) .
— indicates the switch is disabled (CLOSED).
A blank space indicates that the switch setting is not applicable and
can be either OPEN or CLOSED.
n o i t a r u g i f n o C 1 t r o P 2 t r o P 3 t r o P 4 t r o P
1 t r o P 2 t r o P 3 t r o P 4 t r o P D F 1 N A 1 M 0 0 1 2 N A 2 M 0 0 1 3 N A 3 M 0 0 1 4 N A 4 M 0 0 1
N A N A N A N A + + + +
N A N A N A ll u F 0 0 1 + + + + — +
N A N A N A f l a H 0 0 1 — + + + — +
N A N A N A ll u F 0 1 + + + + — —
N A N A N A f l a H 0 1 — + + + — —
N A N A ll u F 0 0 1 ll u F 0 0 1 + + + — + — +
N A N A ll u F 0 0 1 ll u F 0 1 + + + — + — —
N A N A f l a H 0 0 1 f l a H 0 0 1 — + + — + — +
N A N A ll u F 0 1 ll u F 0 1 + + + — — — —
N A N A f l a H 0 1 f l a H 0 0 1 — + + — — — +
N A ll u F 0 0 1 ll u F 0 0 1 ll u F 0 0 1 + + — + — + — +
N A f l a H 0 0 1 f l a H 0 0 1 f l a H 0 0 1 — + — + — + — +
N A ll u F 0 0 1 ll u F 0 1 ll u F 0 0 1 + + — + — — — +
N A f l a H 0 1 f l a H 0 0 1 f l a H 0 1 — + — — — + — —
N A ll u F 0 1 ll u F 0 1 ll u F 0 1 + + — — — — — —
N A f l a H 0 1 f l a H 0 1 f l a H 0 1 — + — — — — — —
ll u F 0 0 1 ll u F 0 0 1 ll u F 0 0 1 ll u F 0 0 1 + — + — + — + — +
f l a H 0 0 1 f l a H 0 0 1 f l a H 0 0 1 f l a H 0 0 1 — — + — + — + — +
ll u F 0 1 ll u F 0 1 ll u F 0 1 ll u F 0 1 + — — — — — — — —
f l a H 0 1 f l a H 0 1 f l a H 0 1 f l a H 0 1 — — — — — — — — —
ll u F 0 1 ll u F 0 0 1 ll u F 0 1 ll u F 0 0 1 + — — — + — — — +
f l a H 0 1 f l a H 0 0 1 f l a H 0 1 f l a H 0 0 1 — — — — + — — — +
ll u F 0 1 ll u F 0 1 ll u F 0 0 1 ll u F 0 0 1 + — — — — — + — +
f l a H 0 0 1 f l a H 0 0 1 f l a H 0 1 f l a H 0 1 — — + — + — — — —
The table below displays sample port configurations and the DIP switch
settings used to obtain them. The configuration column gives the auto-
negotiation, speed and duplex options for each port. By default, all four
ports are set to auto-negotiate.