Marantz SR8000 - Manual (Page 20)

16
ENGLISH
MULTI ROOM SELECTOR
The Multi Room Selector is a function which allows you to listen to the
same or a different source in a room other than the room in which the
SR8000 is located. To use this function, a multi room remote unit and
remote control signal receiver available from your Marantz dealer are
necessary. The operations possible with the multi room function are
explained briefly below. For details, refer to the instruction manual
supplied with the multi room remote control unit and receiver.
MULTI ROOM SELECTOR OPERATION
1. Press the MULTI button o. The unit enters multi room mode and
the display indicates “SEL SOURCE” and flashes the “MULTI”
indicator for approx. 10 seconds. In this time, you can select the
input source by pressing the
FUNCTION SELECTOR button t
and you can set sleep timer for multi room by pressing by the
SLEEP button !0.
2. Then, the display indicates “MULTI VOL” “VOLUME xx dB” for
approx. 5 seconds. At this time, you can set the volume level of
the multi room by turning the volume control knob.
MULTI ROOM SELECTOR OPERATION (USING THE MULTI
ROOM REMOTE CONTROL UNIT)
1. If Video output for multi room is connected to the TV in your
second zone, the on screen display for this video signal will be
shown as follow.
2. Press the MULTI button, the POWER ON button, or select the
desired source on multi room remote control unit from the MULTI
ROOM. Any of these operations will put the SR8000 into multi
room mode and “MULTI” will light in the display and OSD system
for the TV in the multi room will be shown.
3. Press the VOL.UP or VOL.DOWN button on the multi room
remote control unit to set the desired sound volume.
4. In multi room mode, the multi room remote control unit can be
used in the multi room to operate the following functions.
You can select a tuner preset channel and tuning up or down,
and direct selection. And you can control the CD player LD
player, DVD player and tape deck connected to the SR8000.
5. Additionally, SLEEP timer function for multi room is available from
second zone, by the same way as setting the sleep timer for main
room.
6. The status of the main room setting can be monitored from the
second zone with the OSD.
Caution:
If the main room and the secondary room are listening to the same
source, the main room will have priority over controlling that
source. For example, you cannot change the frequency or preset
of the Tuner from a remote location if the main room is also
listening to that source.
O N S C R E E N D I S P L A Y
INFOMATION
The on-screen display, which can be activated by the Main unit or
remote, appears on the TV screen to show the current setting status
of the SR8000.
1. GENERAL INFORMATION
When the OSD button is pressed, the current setting are displayed on
the TV monitor.
This display disappears automatically in about 10 seconds after the
button is pressed.
q VIDEO SOURCE:
Displays the current video source being selected with the function selector
TV, LD, DVD, VCR1, DSS or AUX .
w AUDIO SOURCE:
Displays the current audio source being selected with the function selector
FM, AM, CD, TAPE, CD-R, TV, LD, DVD, VCR1, DSS or AUX .
e DIGITAL INPUT:
Displays the digital input that you are using
DIG-1, DIG-2, DIG-3 , DIG-4 , DIG-5, or DIG-6 .
r DIGITAL OUTPUT:
Displays the digital output that is being used for recording
SOURCE , DIG-1, DIG-2, DIG-3 , DIG-4 , DIG-5, DIG-6 or OFF .
t SURROUND MODE:
Displays the current surround mode
AUTO, DOLBY, DTS-CINEMA, DTS-MUSIC, HALL, MATRIX,
MOVIE , 5-STEREO , STEREO , S-DIRECT
or 6CH INPUT .
y MULTI ROOM
Displays the current status of the Multi Room function.
u MASTER VOLUME
Displays the current volume level.
The volume level is higher at the right of the display, and the pointer
changes to “ ” at 0 dB.
Note:
The On-Screen Display signals for the main room can be output
from the TV MONIcomposite video (RCA) output and the TV MONI,
S-Video output jacks.
With some video equipment or software, the On-Screen Display
characters may be distorted due to noise or tracking adjustment
error.