Manual control, Manual control (man), Adjustment (adj) – MartinLogan MAC 500/E User Manual
Page 15: Stand-alone sequences, Demonstration programs (demo), Test sequences
15
Control Panel
4.
Press the [MENU] and [
↓
] keys at the same time and hold them for 3 seconds until “25” shows in
the display.
5.
Press the
[↑
] and [
↓
] keys until the display shows the temperature measured.
6.
Press [ENTER] to save the setting.
M a n u a l c o n t r o l
M a n u a l c o n t r o l (
M A N
)
The manual control menu permits you to do the following without a controller:
•
reset the fixture (
R S T
)
•
turn the lamp on and off (
L O N
,
L o F F
)
•
open, close, and strobe the shutter at 3 speeds (
S H U T
)
•
control the dimmer (
d I M
)
•
move the color wheels to each position and scroll them at 3 speeds (
C O L 1
,
C O L 2
)
•
move the fixed-gobo wheel to each position (
F g o b
)
•
move the rotating-gobo wheel to each position and rotate the gobos at 3 speeds (
R g o b
)
•
control the focus (
F O C U
)
•
control the iris (
I R I S
)
•
insert and rotate the prism (
P R I S
) at 3 speeds, or, if a frost filter is installed, vary the frost (
F R O S
)
•
control pan and tilt (
P A N
,
T I L T
)
A d j u s t m e n t (
A d J
)
The adjustment menu provides manual control for making mechanical adjustments. These should be performed by a
qualified technician. The menu provides functions to reset the fixture (
R S T
), turn on and off the lamp (
L
O N
,
L o F F
), control all effects in the head (HEAd), and move the head to the home and extreme positions (
P A T I
). The
H E A d
submenu allows the technician to:
•
open, close, and strobe the dimmer/shutter (
d I M
)
•
move the color and gobo wheels through their positions (
C O L 1
,
C O L 2
,
F g o b
,
R g o b
)
•
move the focus lens to its extreme positions (
F O C U
)
•
open and close the iris (
I R I S
)
•
insert and rotate the prism (
P R I S
)
S t a n d - a l o n e s e q u e n c e s
D e m o n s t r a t i o n p r o g r a m s (
d E M O
)
This menu offers 2 preprogrammed demonstrations. Demo 1 shows each effect individually and in combination with
others at a set home position. Demo 2 pans and tilts within a defined area and shows various effect combinations.
Before running demo 1, set the pan/tilt position (
P A N
,
T I L T
) to a good location for viewing the effects and then
focus (
F O C U
) the beam. Select
S E Q
to run the demo. Demo 2 is similar but instead of defining a home position, you
define an area such as a screen or wall by setting the minimum and maximum pan and tilt positions (
M I N P
,
M A X P
,
M I N T
,
M A X T
). Focus the beam in the center of the area.
Te s t s e q u e n c e s
7HVW VHTXHQFH
T S E Q
Run a general test of all effects.
3ULQWHG FLUFXLW ERDUG WHVW
S P E C
P C B T
This menu provides 4 tests of the circuit board for service use:
T I
,
T 2
,
T 3
, and
L E d
.
)DFWRU\ WHVW
S P E C
F T S T
: This menu provides an effects test (
E T S T
), a movement test (
M T S T
), and a sensor
test (
S T S T
) used for quality control. The sensor test includes programs for testing sensors on the color and gobo
wheels (
C O L 1
,
C O L 2
,
R g o b
, and
F g o b
).