MACKIE SRM350 - Manual (Page 17)

17
SRM350v2 SPECIFICATIONS
Enclosure Construction Features
Basic Design Asymmetrical Trapezoidal
Material Polypropylene
Finish Black textured finish
Handles One on side, one on top
Grille Perforated metal with
weather-resistant coating
Line Input Power
Power Consumption 120 watts with musical program and
LIMIT LED blinking
US 120 VAC, 60 Hz
Recommended Amperage Service 2.5 amps
Europe 230 VAC, 50 Hz
Recommended Amperage Service 1.25 amps
Japan 100 VAC, 50/60 Hz
Recommended Amperage Service 3.0 amps
AC Connector 3-pin IEC 250 VAC
Note: The SRM350v2 does not support multiple voltage configurations.
Make sure the voltage rating for your particular model (as indicated
on the rear panel near the IEC socket) corresponds with your local AC
mains voltage.
Control System Functions
Electronic Crossover
Phase Alignment
Equalization
Parametric Equalization
Safety Features
Protection Low-frequency Dynamic Bass Protection,
Power Supply, and Amplifier Thermal Protection
Display LEDs Signal, Power, Limit
Physical Properties
Height 20.75 in / 527 mm
Width 13.10 in / 333 mm
Depth 12.25 in / 311 mm
Weight 26 lb / 11.8 kg
Mounting Methods
Optional hanging brackets for top and bottom of enclosure
(SRM350v2 Bracket Kit: Part No. 0016404).
Never attempt to suspend the cabinet by its handles.
The SRM350v2 is pole-mountable via the built-in socket on the bottom of
the cabinet. Be sure the pole is capable of supporting the weight of the
SRM350v2.
Disclaimer
Since we are always striving to make our products better by incorpo-
rating new and improved materials, components, and manufacturing
methods, we reserve the right to change these specifications at any time
without notice.
“Mackie” and the “Running Man” figure are registered trademarks of
LOUD Technologies Inc.
All other brand names mentioned are trademarks or registered trade-
marks of their respective holders, and are hereby acknowledged.
©2004-2011 LOUD Technologies Inc.
All Rights Reserved.
System Specifications
Frequency Response (–3 dB)
83 Hz - 18.5 kHz
Frequency Range (–10 dB)
61 Hz - 22 kHz
Max SPL Long-Term @ 1m 118 dB
Max SPL Peak @ 1m 121 dB
Crossover Linkwitz-Riley
24 dB/octave @ 2400 Hz
Audio
Input Type Balanced Differential
Input Impedance 94k ohms
Sensitivity (center detent)
Line: +4 dBu
Mic: –36 dBu
Maximum Input Level +22 dBu
Acoustic Contour Equalization (peaking)
+3 dB @ 100 Hz,
+3 dB @ 12 kHz
Operating Temperature Range
–10ºC - 45ºC (14ºF - 113ºF)
Power Amplifiers
Low-Frequency Power Amplifier
Rated Power 165 watts continuous*
Rated THD < 0.03%
Cooling Convection Extrusion
Design Class D
High-Frequency Power Amplifier
Rated Power 30 watts continuous*
Rated THD < 0.03%
Cooling Convection Extrusion
Design Class AB
* Rated power is continuous rms wattage into transducer’s rated imped-
ance @ 1 kHz for the HF amplifier and @ 100 Hz for the LF amplifier.
Transducer Specifications
Low-Frequency Transducer
Diameter 10 in / 250 mm
Voice Coil Diameter 2.0 in / 51 mm
Sensitivity (1W@1m) 96 dB
Power Handling 250 watts rms, long-term
Frequency Range 61 Hz - 3 kHz
High-Frequency Transducer
Diaphragm Diameter 1.4 in/36 mm
Horn Exit Diameter 1 in/25.4 mm
Diaphragm Material Titanium
Sensitivity (1W@1m) 104 dB
Nominal Impedance 16 ohms
Power Handling 75 watts rms, long-term
Frequency Range 1 kHz - 20 kHz
Horn Design
Horizontal Coverage
90º (1 kHz - 20 kHz)
Vertical Coverage
80º (1 kHz - 20 kHz)
Mouth Size
11.1 in x 6.1 in (283 mm x 154 mm)