Grizzly G0690 - Manual (Page 35)

Model g0690/g0691 (Mfg. 11/10+)
-33-
Basic Controls
ON/OFF Switch: starts and stops the motor.
Safety pin & Chain: When installed (Figure 40),
disables the switch to prevent accidental startup.
safety
pin
Figure 40. oN/oFF switch disabled.
oN
switch
safety
pin
Blade Tilt: to adjust the blade tilt, loosen the
blade tilt lock, turn the blade tilt handwheel to
position the blade at the desired angle, then
tighten the lock shown in
Figure 41.
Figure 41. Basic table saw controls.
Blade height
lock
Blade tilt
lock
Fence lock
Blade height
handwheel
Blade tilt
handwheel
Blade height: to set the blade height, unlock the
blade height lock, turn the handwheel to set the
blade height approximately
1 ⁄
4
" higher than the
workpiece, then re-tighten the blade height lock.
Fence Lock: after adjusting the fence to the
desired width of cut, lock it in place by firmly push-
ing the fence lock down until it stops.
Non-Through &
Through Cuts
:mVbeaZh d[ cdc"i]gdj\] Xjih ^cXajYZ YVYdZh
VcYgVWWZih#Cdc"i]gdj\]Xjih]VkZV]^\]Zgg^h`
d[^c_jgn[gdb`^X`WVX`WZXVjhZi]ZWaVYZ\jVgY
bjhiWZgZbdkZY#=dlZkZg!i]Zg^k^c\`c^[ZBJHI
WZ^chiVaaZYWZXVjhZ^ihi^aaegdk^YZhhdbZegdiZX"
i^dc#L]ZcbV`^c\cdc"i]gdj\]Xjihl^i]VYVYd
WaVYZ!YdcdiViiZbeiidXjii]Z[jaaYZei]^cdcZ
eVhh#>chiZVY!iV`Zbjai^eaZa^\]ieVhhZhidgZYjXZ
i]ZadVYdci]ZWaVYZ#6YVYdWaVYZhbVaaZgi]Vc
&%"l^aagZfj^gZgZbdkVad[i]Zg^k^c\`c^[Z!WZXVjhZ
i]Zg^k^c\`c^[Zl^aaWZ]^\]Zgi]Vci]ZWaVYZ#
Non-Through Cuts
Figure 42. Example of a non-through cut.
6 cdc"i]gdj\] Xji ^h V hVl^c\ deZgVi^dc l]ZgZ
i]ZWaVYZYdZhcdiegdigjYZVWdkZi]Zide[VXZd[
i]ZlddYhidX`!Vhh]dlc^ci]Z
FigureWZadl#
Figure 43. Example of a through cut (blade
guard not shown for illustrative clarity).
Through Cuts
6i]gdj\]Xji^hVhVl^c\deZgVi^dc^cl]^X]i]Z
ldg`e^ZXZ^hXdbeaZiZanhVlci]gdj\]!Vhh]dlc
^ci]Z
FigureWZadl#:mVbeaZhd[i]gdj\]XjihVgZ
g^eXjih!XgdhhXjih!b^iZgXjih!VcYWZkZaZYXjih#
I]ZWaVYZ\jVgYVhhZbWanBJHIWZjhZYl]Zc
eZg[dgb^c\i]gdj\]Xjih#