Cdx-2410 – Gemini Industries CDX-2410 User Manual

Page 5

on the track, TIME REMAINING on the disc and TIME RE-

MAINING on the track. Time is measured in minutes, sec-

onds and frames.

PGM: Allows you to create a set playlist. To program a set

list into the CDX-2410 memory, begin by stopping the unit

from play and pressing PGM to begin the set list. Select a

track by using the track selection rotary to scan to the first

track to be placed in the set list. When you have selected the

proper track press PGM and the CDX-2410 will be ready to

set your next selection. Repeat the previous steps until you

have completed your play list, then press play to begin the

set list.

REPEAT: Press the repeat button once to engage 1 once or

repeat the selected track. Press REPEAT again to engage

ALL setting, which will repeat all the tracks on the CD. Press

REPEAT again to disengage the repeat function

SINGLE: Pressing the SINGLE button engages SINGLE

mode, in this mode the CDX-2410 will play one song and

then stop. Pressing the SINGLE button again will then acti-

vate CONTINUOUS mode causing the unit to play continu-

ously (after the last track, the unit will return to the first track

of the disc and continue to play).

TIME: The TIME button switches the time display between

three available sources, these three are TIME ELAPSED on

the track, TOTAL REMAIN on the disc and REMAIN on the

track. TIME ELAPSED indicates how much time has cur-

rently gone by since the play button was pressed, TOTAL

REMAIN will count down the time remaining on the entire

disc and REMAIN counts down the time that is left before the

end of the track.

PITCH: Hold the PITCH button to activate the PITCH CON-

TROL SLIDE. Press the PITCH button to switch between +/-

4%, 8%, and 16% pitch ranges that can be controlled through

the use of the PITCH CONTROL SLIDER. Hold the PITCH

button again to deactivate this mode.

PITCH CONTROL SLIDE: Moving the PITCH CONTROL

SLIDE up or down will change the pitch percentage +/ - 4,

8, or 16%.

PITCH BEND: Pushing the PITCH BEND BUTTONS will au-

tomatically raise the pitch up to +16% or lower the pitch down

to -16% from the existing pitch setting. Releasing the buttons

will return the pitch to the original pitch setting. You can use

this function to match the beat when mixing from one song

to another.

LOOP SECTION: A LOOP repeats the section between the

entry point (LOOP IN) and the exit point (LOOP OUT).

A. To set a loop while the unit is playing, start by pressing

the LOOP IN BUTTON (it will light up)

B. When you reach the desired end loop point press the

LOOP OUT BUTTON (it will also light up). The LOOP IN

and LOOP OUT buttons will blink. The loop will continue

playing until you press the LOOP OUT BUTTON again al-

lowing the music to continue from that point on.

C. To re-engage the loop you must press the RELOOP

BUTTON.

D. When you have released your loop the LOOP IN and

LOOP OUT BUTTON buttons will turn OFF and the will re-

main lit to indicate that your loop is stored in the CDX-2410

memory.

E. Pressing the LOOP IN BUTTON again while the unit is

playing will erase the previously saved loop while saving

your new loop entry point.

F. Press LOOP OUT to exit the loop and save a new com-

plete loop.

G. Press RELOOP to return to the beginning of the previ-

ously saved loop from normal play. Press RELOOP repeat-

edly to cause the loop to stutter.

NOTE: THE FIRST LOOP WILL HAVE A PAUSE AT THE EXIT

POINT, WHILE ALL OTHERS WILL BE SEAMLESS.

PLAY / PAUSE: Each press of the PLAY / PAUSE BUTTON

causes the operation to change from PLAY to PAUSE or from

PAUSE back to PLAY. The PLAY/PAUSE BUTTON remains lit

when in PLAY mode, while it blinks in PAUSE mode.

CUE: To set a CUE point, press the PLAY/PAUSE BUTTON

while a file is playing and use the JOG WHEEL to locate a

desired CUE point. Pressing the PLAY/PAUSE BUTTON again

will set the CUE point. While the unit is playing and after the

cue point has been programmed, pressing CUE will cause the

CD player to enter the PAUSE mode (PLAY/PAUSE BUTTON

blinks) at the programmed cue point (the CUE LED is lit). Hold-

ing down the CUE button changes the function to preview, and

allows you to stutter start or play from the programmed CUE

POINT. Releasing the CUE button will return the CD to the

preset CUE point.

TRACK SELECTION ROTARY: The TRACK SELECTION RO-

TARY allows you to select the next or previous track by either

turning it clockwise to go forward or counter-clockwise to go

back. Select the track desired by pressing the TRACK SELEC-

TION ROTARY.

NOTE: ONCE YOU HAVE SKIPPED TO ANOTHER TRACK,

YOU MAY NOT GO BACK TO YOUR PROGRAMMED CUE

POINT. YOU MUST BEGIN YOUR CUE SELECTION OVER

AGAIN, THE CUE WILL BE PRESET TO THE BEGIN-NING

OF THE NEWLY SELECTED TRACK.

BRAKE: To engage the BRAKE function, press the BRAKE

button, then the PAUSE button to perform the brake effect. To

restart the song, press the PAUSE button.

REVERSE: When the REVERSE button is pressed, the file

that is currently playing begins to play in reverse mode.

CDX-2410