Inventory, Notice – Grizzly H8172 User Manual
Page 10

-8-
H8172 Cement Mixer
Figure 1. Inventory components picture 1.
A
B
C
D
Inventory
After all the parts have been removed from the
carton, you should have:
Main Components (Figures 1 & 2)
Qty
A. Lower Drum ................................................ 1
B. Motor Assembly .......................................... 1
C. Tipping Wheel ............................................ 1
D. Upper Drum ................................................ 1
E. Support Leg ................................................ 1
F. Frame ......................................................... 1
G. Axle Bracket ............................................... 1
H. Mixing Blades ............................................. 2
I. Wheels ....................................................... 2
J. Bearing Block ............................................. 1
K. Upper Bracket ............................................ 1
L. Gasket (not shown) .................................... 1
Figure 2. Inventory components picture 2.
E
F
G
H
I
J
K
Hardware
Qty
Hairpin Cotter Pin (Wheels) .............................. 2
Hex Bolts M8-1.25 x 65 (Leg to Frame) ............ 2
Flat Washers 8mm (Leg to Frame) ................... 2
Lock Washers 8mm (Leg to Frame) ................. 2
Hex Nuts M8-1.25 (Leg to Frame) .................... 2
Hex Bolt M6-1 x 25 (Plunger Rods) .................. 1
Lock Nut M6-1 (Plunger Rods) .......................... 1
Cotter Pin (Plunger Rod) ................................... 1
Hex Bolts M8-1.25 x 65 (Bracket to Frame) ..... 2
Flat Washers 8mm (Bracket to Frame) ............. 2
Lock Washers 8mm (Bracket to Frame) ........... 2
Hex Nuts M8-1.25 (Bracket to Frame) .............. 2
Hex Bolts M8-1.25 x 60 (Bearing Block) ........... 1
Flat Washers 8mm (Bearing Block) .................. 1
Lock Washers 8mm (Bearing Block) ................. 1
Hex Nuts M8-1.25 (Bearing Block) .................... 1
Hex Bolts M8-1.25 x 20 (Upper Bracket) .......... 2
Flat Washers 8mm (Upper Bracket) .................. 2
Lock Washers 8mm (Upper Bracket) ................ 2
Hex Nuts M8-1.25 (Upper Bracket) ................... 2
Phillips Screws M10-1.5 x 20 (Blade/Lower) .... 2
Plastic Washers 10mm (Blade/Lower) .............. 2
Flat Washers 10mm (Blade/Lower) ................... 2
Lock Washers 10mm (Blade/Lower) ................. 2
Hex Nuts M10-1.5 (Blade/Lower) ...................... 2
Hex Bolts M8-1.25 x 20 (Drum Pieces) ........... 10
Flat Washers 8mm (Drum Pieces) .................. 10
Lock Washers 8mm (Drum Pieces) ................ 10
Phillips Screws M10-1.5 x 20 (Blade/Upper) .... 2
Flat Washers 10mm (Blade/Upper) ................... 2
Lock Washers 10mm (Blade/Upper) ................. 2
Hex Nuts M10-1.5 (Blade/Upper) ...................... 2
Hex Bolt M8-1.25 x 65 (Motor Assembly) ......... 1
Flat Washers 8mm (Motor Assembly) ............... 3
Lock Washers 8mm (Motor Assembly) ............. 3
Hex Nuts M8-1.25 (Motor Assembly) ................ 3
Hex Bolts M8-1.25 x 20 (Tipping Wheel) .......... 2
Flat Washers 8mm (Tipping Wheel) .................. 2
Lock Washers 8mm (Tipping Wheel) ................ 2
Hex Nuts M8-1.25 (Tipping Wheel) ................... 2
If any nonproprietary parts are missing (e.g. a
nut or a washer), we will gladly replace them; or
for the sake of expediency, replacements can be
obtained at your local hardware store.
NOTICE
Some hardware/fasteners on the inventory
list may arrive pre-installed. Check mount-
ing locations before assuming that any
items from the inventory list are missing.