Graco PACK N PLAY 9046 - Manual (Page 6)

9 361-10-99 10 11 12
Parent Organizer*
Step 1.
Your parent organizer
includes two plastic dividers.
Slide the plastic dividers
into the two pockets in the
section dividers of the
parent organizer.
Step 2.
Slide the tube into the
mounts on the end of
your unit.
Push the button in to
get it started.
Pull up on the parent
organizer to make sure
that the buttons are
caught on the bottom
of the mounts.
Step 3.
To remove the parent
organizer push in on the
buttons on the bottom of
the tubes and pull up.
Step 1.
Remove the mattress from your bassinet.
Step 2.
Unsnap the end flaps from your Pack ’N Play.
Step 3.
Pull back the fabric at one corner of the bassinet to find the
red spring latch.
Step 4.
Pull the red spring latch back
and lift up the tube.
Step 5.
Pull the tube out of the bassinet
and set aside.
Step 6.
Repeat steps 3, 4 and 5 to remove the other tube.
Step 7.
Use extreme
care when pulling the tubes
apart.
Pull the tubes apart by twisting
the tubes as you pull. Store the
tubes in the pockets in the
bassinet.
To Install Your Bassinet
PARTS LIST
CHECK that you have all the parts listed below
BEFORE assembling your bassinet.
No tools required.
Bassinet
Tube (2)
Tube (2)
Loop end Wire end
Red spring
latch end
Round end
To Remove Your Bassinet Step 4.
Install the end of the tube
without the red spring latch
by placing the loop end into
the slot in the plastic corner.
Step 5.
On the other end of the tube,
pull back on the red spring
latch and insert the loop into
the slot in the plastic corner.
Step 6.
Repeat steps 4 and 5 on the
other side of the bassinet.
Step 7.
Snap both of the end flaps of
the bassinet to the Pack ’N
Play with the eight snaps
(four on each end).
Step 8.
Place the mattress in the
bassinet soft side up. Push
down on the mattress to
secure the mattress to the
VELCRO ®
on the bassinet.
DO NOT use your bassinet
without the mattress
provided by Graco.
The four bassinet tubes are located in storage pockets
sewn into the bassinet itself.
Step 1.
Insert wire end of one tube
into the round end of a tube
with a red spring latch.
Repeat with other tubes.
Step 2.
Slide the assembled tubes
into the tunnels on the sides
of the bassinet.
Step 3.
Lift bassinet by the two tubes and lower it into the
Pack ’N Play. Make sure the printed warnings on
the end flap are facing up.
The loop ends must be in the slots in the
corners to secure the bassinet in the Pack ’N Play. Pull
up on the tube and bassinet to ensure that the tube is
in place.
To avoid SUFFOCATION, DO NOT use
extra padding such as a water mattress, mattress, or
pillows inside the bassinet. Use ONLY mattress
provided by Graco.
Your bassinet is now ready to use.
Casters*
To apply the locks, push
DOWN on the levers.
To release the locks, lift UP
on the levers.
Wheels*
To apply the locks, push
DOWN on the levers.
To release the locks, lift UP
on the levers.
Side Flap*
You can raise side flap if desired.
Unfasten
VELCRO ® straps at
bottom of flap. Roll flap up.
Fasten in place with snap loops at
top.
Cargo Bag*
The cargo bag can be snapped
onto the end of the Pack ’N Play
for easy access. Unzip both ends
and tuck inside the bag.
Maximum weight 5 lbs (2.3 kg).
Button
BASSINET INSTRUCTIONS
ACCESSORY INSTRUCTIONS
ON CERTAIN MODELS*
Always keep objects out of child’s
reach. Remove parent organizer when child is able
to pull himself up in the Pack ’N Play.