beautypg.com

1 before initial start-up, 2 check transfer switch operation, 3 electrical checks – Guardian Technologies 04758-2 User Manual

Page 12: Danger

background image

• Remove watches, rings or other metal objects;
• Use tools with insulated handles;
• Wear rubber gloves and boots;
• Do not lay tools or metal parts on top of the

battery; and

• Disconnect charging source prior to connecting or

disconnecting battery terminals.

Do not open or mutilate the battery. Released

electrolyte has been known to be harmful to the
skin and eyes, and to be toxic.

The electrolyte is a dilute sulfuric acid that is

harmful to the skin and eyes. It is electrically
conductive and corrosive.

The following procedures are to be observed:
• Wear full eye protection and protective clothing;
• Where electrolyte contacts the skin, wash it off

immediately with water;

• Where electrolyte contacts the eyes, immediately

flush thoroughly with water and seek medical
attention; and

• Spilled electrolyte is to be washed down with an

acid neutralizing agent. A common practice is to
use a solution of 1 pound (500 grams) bicarbonate
of soda to 1 gallon (4 liters) or water. The bicar-
bonate of soda solution is to be added until the
evidence of reaction (foaming) has ceased. The
resulting liquid is to be flushed with water and the
area dried.

Lead-acid batteries present a risk of fire because

they generate hydrogen gas. The
following procedures are to be followed:

• DO NOT SMOKE when near the battery;
• DO NOT cause flame or spark in battery area; and
• Discharge static electricity from body before touch-

ing the battery by first touching a grounded metal
surface.

Be sure the AUTO/OFF/MANUAL switch is set to

the OFF position before connecting the battery
cables. If the switch is set to AUTO or MANUAL,
the generator can crank and start as soon as the
battery cables are connected.

Be sure the utility power supply is turned off, or

sparking may occur at the battery posts as the
cables are attached and cause an explosion.

2.1 BEFORE

INITIAL

START-UP

Before starting, complete the following:

1. Set the generator’s main circuit breaker to its

OFF (or open) position.

2. Set the generator's AUTO/OFF/MANUAL switch to

the OFF position.

3. Turn OFF the utility power supply to the transfer

switch using the means provided (such as the
utility main line circuit breaker).

4. Check the engine crankcase oil level and, if neces-

sary, fill to the dipstick FULL mark with the rec-
ommended oil. Do not fill above the FULL mark.

5. Check the fuel supply. Gaseous fuel lines must

have been properly purged and leak tested in
accordance with applicable fuel-gas codes. All
fuel shutoff valves in the fuel supply lines must
be open.

Never operate the engine with the oil level

below the “Add” mark on the dipstick. Doing
this could damage the engine.

2.2

CHECK TRANSFER SWITCH
OPERATION

Refer to Section 3.5, of the owner’s manual for man-
ual operation procedures.

DANGER

Do not attempt manual transfer switch opera-

tion until all power voltage supplies to the
transfer switch have been positively turned off.
Failure to turn off all power voltage supplies
will result in extremely hazardous and possibly
fatal electrical shock.

2.3 ELECTRICAL

CHECKS

Complete electrical checks as follows:

1. Turn on the utility power supply to the transfer

switch using the means provided (such as a utility
main line circuit breaker).

DANGER

The transfer switch is now electrically “hot.”

Contact with “hot” parts will result in extremely
hazardous and possibly fatal electrical shock.
Proceed with caution.

2. Use an accurate AC voltmeter to check utility

power source voltage across terminals N1 and
N2. Nominal line-to-line voltage should be 240
volts AC.

Section 2 — Post Installation Start-up and Adjustments

Air-cooled 7 kW, 12 kW and 15 kW Generators

10