Generac Power Systems 005223-0 - Manual (Page 47)

1 033212 4 SCREW HHC 5/16-18 X 1-1/4 G5
2 075580 1 FLANGE FUEL INLET
3 0F6390 1 REGULATOR ASSEMBLY DUAL FUEL
4 039253 2 SCREW HHC M8-1.25 X 20 G8.8
5 022145 2 WASHER FLAT 5/16-M8 ZINC
6 022129 6 WASHER LOCK M8-5/16
7 045771 2 NUT HEX M8-1.25 G8 CLEAR ZINC
9 0E8286 1 STREET EL 45 DEG 1/2" NPT BRASS
10 026812 2 ELBOW 90D 3/4 NPT
11 0F8379 1 NIPPLE PIPE 3/4 NPT X 7”
12 0F3869 1 (REF.) SWITCH PRESSURE GAS 5" RISE (INCLUDED WITH I/N 3)
13 057823 2 CLAMP HOSE #10 .56-1.06
14 059194 1 HOSE 5/8 ID LPG & NG (31.5” LG)
15 064945 1 GASKET CARB ADAPTOR
16 0D1509 1 DECAL INLET PRESSURE
17 * 050279 1 DECAL FUEL INLET NG (NATURAL GAS APPLICATION)
050280 1 DECAL FUEL INLET LPG (LP VAPOR APPLICATION)
18 0E7839 1 MACHINING CARBURETOR ADAPTOR
19 0E6586 1 GASKET BOSCH 32 & 40
20 0E4394 1 ACTUATOR BOSCH 40 GOVERNOR
21 040105 1 HOSE COOL 2IN ID 20R4 (2” LG)
22 0E6382B 1 (REF) VENTURI HOLDER W/40MM ACTUATOR
23 0E7121 1 (REF) O-RING 47.625 ID X 2.38 WIDTH
24 0E6376B 1 (REF) VENTURI 28 ID THROTTLE W/CHOKE
25 042561 2 CLAMP HOSE #36 1.88-2.75
26 0E9295 1 ASSY THROTTLE 28MM
27 061012 1 PLUG STD PIPE 1/8 SOCKET HEAD
28 022097 4 WASHER LOCK M6-1/4
29 044118 1 BARBED STR 1/2 NPT X 5/8
30 046580 4 SCREW SHC M6-1.0 X 45 G12.9
31 026915 2 NIPPLE CLOSE 3/4 X 1.375
33 0F6155 1 HARNESS CPL FUEL JUMPER
NOTES:
1.
REGULATOR (I/N 3) AS SHOWN IN ILLUSTRATION IS SET UP FOR
NATURAL GAS APPLICATION.
2. TO CONFIGURE REGULATOR FOR LP VAPOR, SWITCH HOSE BARB,
HOSE CLAMP (I/N 13) AND HOSE (I/N 14) FROM “OUT-1” TO “OUT-2”.
REPLACE PIPE PLUG FROM “OUT-2” TO “OUT-1”. USE PIPE SEALANT
ON HOSE BARB AND PIPE PLUG. MAKE SURE TO KEEP PORTS FREE
FROM DEBRIS DURING RECONFIGURATION PROCESS.
3*. FOR LP VAPOR APPLICATION SUBSTITUE LPG FUEL INLET DECAL P/N
050280 FOR NG FUEL INLET DECAL P/N 050279 (ITEM17).
4 . WHEN SWITCHING FUEL TYPES, THE PROPER DIP SWITCH SITTINGS
MUST BE MADE TO THE CONTROL PANEL. SEE OWNERS MANUAL, FUEL
SECTION FOR MORE DETAILS.