beautypg.com

User instructions, Turning off the stove, Upgrading your stove – Stovax Ceramica Gazco Ceremica Log Effect Stove Range User Manual

Page 5: Handling & disposal of fire ceramics, Cleaning the fire, Fuel bed arrangements

background image

5

3. TURNING OFF THE STOVE

3.1 To turn the stove off, locate the control valve, turn the left-

hand control knob until it points to off ( ). The main burner

will go out leaving the pilot burning.

3.2 To turn the pilot off, locate the control valve, turn the right-

hand control knob until it points to off ( ), the pilot will go

out.

4. UPGRADING YOUR STOVE

4.1 Your stove is fitted with a control valve that can be easily

upgraded to battery powered remote control. This upgrade

can be fitted by anyone capable of simple DIY jobs and

requires no special training. There are two versions of this

control which can be obtained through your local Gazco

stockist.

4.2 STANDARD REMOTE CONTROL This remote control can

control the gas appliance after the pilot has been lit. It can

turn the main burner on and regulate it from low through to

high and back again. It can turn the main burner off leaving

the pilot burning. GAZCO PART NUMBER 8455.

4.3 THERMOSTATIC AND TIMER REMOTE CONTROL This

remote control can control the gas appliance after the pilot

has been lit. In ‘MANUAL MODE’ it can be used to turn the

main burner on and manually regulate it from low through

to high and back again. It can also be used to turn the main

burner off leaving the pilot burning. In ‘AUTO MODE’ it will

automatically regulate the room temperature. In ‘TIMER

MODE’ it will turn the fire on and off according to a pre-set

programme and automatically regulate the room

temperature during two ON periods. GAZCO PART

NUMBER 8456.

5. HANDLING & DISPOSAL OF FIRE CERAMICS

The fuel effect and side panels in this appliance are made

from Refractory Ceramic Fibre (RCF), a material which is

commonly used for this application.
Protective clothing is not required when handling these

articles, but we recommend you follow normal hygiene rules

of not smoking, eating or drinking in the work area and

always wash your hands before eating or drinking.
To ensure that the release of RCF fibres are kept to a

minimum, during installation and servicing a HEPA filtered

vacuum is recommended to remove any dust accumulated

in and around the appliance before and after working on it.

When servicing the appliance it is recommended that the

replaced items are not broken up, but are sealed within

heavy duty polythene bags and labelled as RCF waste.
RCF waste is classed as stable, non-reactive hazardous waste

and may be disposed of at a licensed landfill site.
Excessive exposure to these materials may cause temporary

irritation to eyes, skin and respiratory tract; wash hands

thoroughly after handling the material.

USER INSTRUCTIONS

6. CLEANING THE FIRE

WARNING: DO NOT ATTEMPT TO CLEAN THE STOVE

UNTIL IN A COLD CONDITION. THE STOVE RETAINS

ITS HEAT FOR A CONSIDERABLE TIME AFTER

SHUTDOWN.

NOTE: THE CAST IRON DOOR IS HEAVY, TAKE EXTREME

CARE WHEN HANDLING.

6.1 Remove the door by undoing the four dome nuts using the

tool supplied and place to one side.

6.2 Carefully remove the ceramic fuel bed components and

place to one side taking care to protect floor coverings etc.

PLEASE HANDLE WITH CARE.

6.3 The logs should not require cleaning. Do not use a vacuum

cleaner or brush to clean the logs. Any large pieces of debris

may be removed by hand.

6.4 Ensure any debris is removed from the burner ports.
6.5 Replace the ceramics and door referring to Section 7 below.
6.7

Use a damp cloth to clean the outer casing of the

appliance.

7. FUEL BED ARRANGEMENTS

Remove the cast iron door using the tool provided. Remove

the front coal retainer by lifting vertically.
NOTE: THE CAST IRON DOOR IS HEAVY, TAKE EXTREME

CARE WHEN HANDLING TO AVOID DAMAGING THE

OUTER CASING.
The fuel bed consists of 5 logs and 2 ash panels. The logs

have letters A,B,C,D and E moulded into them for

identification.

7.1 Take the rear log A and place it up against the rear of the

fire sitting on the two flat ledges of the burner. The two legs

of the log should sit between the rear burner ports. See

diagram 3. Ensure there is an equal gap between each side

of the log and the side of the firebox.

3

AR1610