FUNAI PY90VG - Manual (Page 10)

10 EN
Functional overview (cont’d)
Before you start
Using a remote control
Keep in mind the following when using the remote
control:
• Make sure that there is no obstacle between the
remote control and the remote sensor on the unit.
• Remote operation may become unreliable if strong
sunlight or fluorescent light is shining on the
remote sensor of the unit.
• Remote control for different devices can interfere
with each other. Avoid using remote control for
other equipment located close to the unit.
• Replace the batteries when you notice a fall off in
the operating range of the remote control.
• The maximum operable ranges from the unit are
as follows.
- Line of sight: approx. 23 feet (7m)
- Either side of the center:
approx. 16 feet (5m) within 30°
- Above: approx. 16 feet (5m) within 15°
- Below: approx. 10 feet (3m) within 30°
Installing batteries in the remote control
Install two “AA” size batteries (supplied) matching the
polarity indicated inside battery compartment of the
remote control.
Note:
Incorrect use of batteries can result in hazards
such as leakage and bursting. Please observe the
following:
• Do not mix new and old batteries together.
• Do not use different kinds of batteries together,
although they may look similar, different batteries
may have different voltages.
• Make sure that the plus and minus ends of
each battery match the indications in the battery
compartment.
• Remove batteries from equipment that is not going
to be used for a month or more.
• When disposing of used batteries, please comply
with governmental regulations or environmental
public instruction’s rules that apply in your country
or area.
• Do not recharge, short-circuit, heat, burn or
disassemble batteries.
ST AND BY-O N
REW F.F WD STO P/EJE CT PLA Y
VC R
CHAN NEL
OP EN/C LOSE
D.D UB BIN G STO P PLA Y VCR DVD DVD REC ORD S-V IDE O VID EO AUD IO
SO URC E
REC ORD
L R
SKIP
REC PAUS E
ETU P TOP MEN U/ ORIG INAL
k
FW D g STO P C PLA Y B REV h H G
Remote
control
Within about
23 feet (7m)
30°
30°
Because this product is a combination of a VCR and a DVD recorder, you must select first which component
you wish to operate with [SOURCE].
STOP
STANDBY-ON TIMER SET TIMER
PREV NEXT
OPEN/CLOSE
SPACE
1 2 3
4 5 6
7 8
0
9
CH
VIDEO/TV
SLOW
PAUSE
.@/: ABC DEF
GHI JKL MNO
PQRS
REC
DISPLAY
TUV WXYZ
DVD REC
REC MODE
ZOOM
SEARCH
VCR
SETUP
CM SKIP
RETURN DISC MENU TITLE
DUBBING
RAPID PLAY
CLEAR
OK
PLAY
AUDIO
VCR DVD
SOURCE
DVD indicator
VCR indicator
SOURCE button
VCR button
DVD button
STANDBY-ON REW F.FWD STOP/EJECT PLAY
VCR CHANNEL
OPEN/CLOSE
D.DUBBING STOP PLAY
VCR DVD
DVD
RECORD
S-VIDEO VIDEO AUDIO SOURCE
RECORD
L R
Press [VCR ] on the remote control.
(Verify that the VCR indicator is lit.)
Press [DVD ] on the remote control.
(Verify that the DVD indicator is lit.)
The VCR/DVD recorder switching
Note:
• Pressing only [SOURCE] on the front panel
DOES NOT switch the mode of the remote
control. You MUST select the correct mode on
the remote control.
• You cannot switch to another mode (DVD or
VCR) during in the timer-standby mode.
• Pressing [DVD REC] or [VCR REC] on the
remote control switches immediately its respective
mode so that you can start recording directly on
the appropriate media.
VCR MODE
DVD MODE
1 2 3
E9A12UD_PY90VG_p01-40.indd 10 E9A12UD_PY90VG_p01-40.indd 10 2006/04/27 17:23:32 2006/04/27 17:23:32