Fender Cyber Foot Controller User Manual
Page 4
w
ww
ww
w.
.f
f e
e n
n d
d e
e r
r.
.c
co
om
m
4
w
ww
ww
w.
. m
m r
r g
g e
e a
a r
r h
h e
e a
a d
d.
.n
ne
et
t
F
F
F
F
e
e
e
e
a
a
a
a
t
t
t
t
u
u
u
u
r
r
r
r
e
e
e
e
s
s
s
s
•
•
•
•
O
O
O
O
v
v
v
v
e
e
e
e
r
r
r
r
v
v
v
v
ii
ii
e
e
e
e
w
w
w
w
C
C
C
C
y
y
y
y
b
b
b
b
e
e
e
e
r
r
r
r
–
–
–
–
S
S
S
S
e
e
e
e
r
r
r
r
ii
ii
e
e
e
e
s
s
s
s
M
M
M
M
I
I
I
I
D
D
D
D
I
I
I
I
F
F
F
F
u
u
u
u
n
n
n
n
c
c
c
c
t
t
t
t
ii
ii
o
o
o
o
n
n
n
n
s
s
s
s
The Fender
®
Cyber Foot Controller™ can be used to
send Program Change and Continuous Controller
messages to any MIDI device, hands-free. Especially
designed to complement Fender Cyber-Series™
amplifiers, the Cyber Foot Controller adds functionality
to any amp that interprets the following messages of the
MIDI specification, (features as they relate to Cyber-
Series amps shown in brackets):
◊
◊ Program Change messages: Use the DOWN and
UP buttons to index by “tens,” then a 0–9 button to
select the “ones” digit. [Selects any preset using the
MIDI map.]
◊
◊ Continuous Controller messages: Use the
CONTINUOUS CONTROLLER pedal to send Control
Change messages. [Adjusts a preset parameter
defined by your amplifier.]
◊ Volume control messages: Use the VOLUME pedal
to adjust the volume on your amplifier. [Adjusts
master volume.]
Cyber-Series™ messages (unspecified MIDI messages
that may be interpreted differently by other amps.)
◊
◊ TAP TEMPO/TUNER BUTTON
•Set the time/rate parameter for the current effect
•
•Activate the on-board tuner.
◊
◊ EFFECTS ON BUTTON
•Engage or bypass the current preset’s effect.
Thank you for choosing Fender
Thank you for choosing Fender
®
®
,
,
—T
—T
one, T
one, T
radition and Innovation—since 1946.
radition and Innovation—since 1946.
A.
TAP TEMPO / TUNER BUTTON
Sets the time/rate parameter for the active effect
with one or more quick presses. A single press will
set the parameter to its maximum value.
or
Activates the TUNER Mode when held down for 2
seconds, (“tun” is displayed). Press any button to
exit TUNER Mode.
Sends a Program Change message to Bank 1,
Program 127.
1
B.
EFFECTS ON (OFF) BUTTON
Alternately engages and bypasses the effects for
the current preset.
Continuous Controller assignment: 85.
Sends alternating Control Change messages:
Data 0 for OFF; Data 127 for ON.
C.
LED DISPLAY
•Displays the last Program Change number
transmitted (flashes “
00_
” until the first
number is selected).
•Displays “tun” in TUNER Mode.
•Displays MIDI Transmit Channel during selection.
D. DOWN (–10) & UP (+10)
BUTTONS
Pre-selects the “tens”
range for a Program
Change number at these
intervals:
0 0 0
↔010↔020↔030↔
0 4 0
↔050↔060↔070↔
0 8 0
↔090↔100↔1 10↔
120
↔000↔
(loop)
...
A Program Change number
is not transmitted until the “ones” digit is selected (see
item {E} below). Note: The display stops flashing when a
DOWN or UP selection returns you to the interval
containing the last Program Change number transmitted.
E.
0, 1, 2, 3, 4, 5, 6, 7, 8, 9
BUTTONS
Selects the “ones” digit of the Program Change
number within the pre–selected “tens” range, and
transmits the Program Change number. For
example, if the display shows, “12_,” pressing the
“7” button will cause “127,” to display and the
Program Change 127 to transmit.
Note: “128” and “129” cannot be selected.
F.
CONTINUOUS CONTROLLER PEDAL
Controls any programmable parameter for the
current preset.
Continuous Controller assignment: 11.
Sends Control Change messages 0–127.
G.
VOLUME PEDAL
Controls the MASTER volume level.
Continuous Controller assignment: 7.
Sends Control Change messages 0–127.
MIDI TRANSMIT CHANNEL SELECTION
Transmit channel is set to 1 by default at power-up. To
select channels (1–16): While holding down
TAP TEMPO/TUNER {A}, press EFFECTS ON {B}, then
release both buttons. Select a channel using the
DOWN and UP buttons {D}, (channel selection is
displayed). Press any “0–9” button to exit.
1
Bank Change #1 is used only to access the TUNER Mode, all other messages ar e prefaced with Bank Change #0, which corresponds
to the MIDI Map on Fender® Cyber-Series™ amplifiers.