ADC AD-78 Instruction Manuals and User Guides
We have 1 Instruction Manual and User Guide for AD-78 ADC
Manuals 
| Recognized languages: | English |
|---|---|
| Pages: | 75 |
| Size: | 428 KB |
Show table of contents
Document Outline
- Retain This Manual In A Safe Place For Future Reference
- Important
- IMPORTANT
- CAUTION
- WARNING
- WARNING
- FOR YOUR SAFETY
- IMPORTANT
- Table of Contents
- Specifications*
- B. COMPONENT IDENTIFICATION
- SECTION III
- INSTALLATION PROCRDURES
- A. LOCATION REQUIREMENTS
- B. UNPACKING/SETTING UP
- C. DRYER ENCLOSURE REQUIREMENTS
- D. FRESH AIR SUPPLY
- E. EXHAUST REQUIREMENTS
- R ELECTRICAL INFORMATION
- I. PREPARATION FOR OPERATION/START-UP
- J. PREOPERATIONAL TESTS
- K. PREOPERATIONAL INSTRUCTIONS
- L. SHUT DOWN INSTRUCTIONS
- A. SERVICE
- B. PARTS
- A. SERVICE
- B. PARTS
- A. RETURNING WARRANTY CARPrS^
- B. PARTS
- C. RETURNING WARRANTY PARTS
- INSTALLATION PROCRDURES
- SECTION VI
- ROUTINE MAINTENANCE
- TROUBLESHOOTING
- A. No L.E.D. (light emitting diode) display (for microprocessor [computer] models ONLY)...
- B. Drive motor |s operating (does not start)...
- C. Drive motor (Reversing Models ONLY) operates in one direction only ... stops and restarts in the same direction •••
- D. Drive motor operates okav for a few minutes, then stops and will not restart...
- O. Microprocessor controller (computer) locks up and L.E.D. (light emitting diode) display reads erroneous message(s) or only partial segments...
- P. Dryer stops during a cycle, microprocessor controller (computer) buzzer (tone) sounds for 5 seconds, and then the L.E.D. display reads “dSFL” for approximately 30 seconds, and then returns to “FILL”...
- Q. Dryer stops during a cycle, microprocessor controller (computer) buzzer (tone) sounds for 5 seconds, and then the L.E.D. returns to “FILL”...
- R. Microprocessor controller (computer) L.E.D. display reads “SEFL”...
- S. Microprocessor controller (computer) L.E.D. display reads “Hot”...
- W. Dryer operates but is taking too iong to dry...
- X. At the completion of the "AUTO" drying/cooling cycle, the load is coming out over dried...
- Y. At the completion of the "AUTO" drying/cooling cycle, the load is coming out still damp...
- Z. Main burners are burning with a yellow flame (for Gas Models ONLY)...
- AA. Condensation on main door glass...
- BB. Scraping noise at basket (tumbler) area...
- CC. Excessive noise and/or vibration...
- A. Dryer will not start...both drive motor and blower (impellor/fan) motor are not operating and indicator light h off...
- B. Drive motor is not operating (does not start)...
- C. Drive motor (Reversing Models ONLY) operates in one direction only... stops and restarts in the same direction...
- D. Drive motor operates okay for a few minutes, then stops and will not restart...
- E. Blower/Fan motor is not operating (does not start)...
- E Blower/Fan motor operates okay for a few minutes, then stops and MU not restart...
- G. Both drive motor and hlower (impellor/fan) motor (Reversing Models ONLY) not operating (do not start) and indicator light is on...
- H. Heating unit is not operating (no heat)...no voltage at heating unit (i.e.. Gas Model > Hot Surface Ignition [HSI] module. Electric Model - electric oven contactor, or Steam Model - steam damper system pneumatic solenoid) when dryer is first started...
- I. № heat)...no voltage at heating unit (i.e., Gas Model - Hot Surface Ignition [HSI] module, Electric Model - electric oven contactor, or Steam Model - steam damper system pneumatic solenoid) •••
- J. Dryer operates but is taking too long to dry...
- K. Main burners are burning with a yellow flame (for Gas Models ONLY)...
- L. Condensation on main door glass...
- M. Scraping noise at basket (tumbler) area...
- N. Excessive noise and/or vibration...
- SECTION VIII
- SECTION IX