Sealey SSB37W - Manual (Page 7)

7.1. After each use clean material out of hopper .
7 .1 .1 . Rinse/dry inside and outside of spreader after each use .
7 .1 .2 . Before operating make sure that the tyres are inflated to the correct pressure i .e . 25psi maximum .
7 .1 .3 . Periodically check all fastenings are tight .
7 .1 .4 . Check the condition of the "media agitator" (12) "R" pin, after continued use . Replace if required .
7 .1 .5 . Annually clean and lightly lubricate cable .
7 .1 .6 . To avoid damaging the spreader never exceed the rated load capacity of 37kg .
7 .1 .7 . use the rain cover (48) when necessary . Avoid using the spreader when raining, unless essential .
7.2. STORAGE.
7 .2 .1 . Before storing ensure that the spreader is clean and dry; fit the rain cover .
7 .2 .2 . Store indoors or in a protected area during severe weather and in the winter months .
7 .2 .3 . DO NOT allow material to stay in the hopper for extended periods of time .
6.9. CALCULATING ThE AMOUNT OF MATERIAL NEEDED. (refer to Charts 'A' & 'B')
The spreader is designed to be pushed at three miles an hour, which is a brisk walking pace . Slower or faster speeds will change the
spread pattern . Wet salt/grit will also change the spread pattern . See fig .13 for media agitator; promoting flow .
To calculate the amount of salt/grit needed, divide the coverage stated on the packaging by the weight of the bag .
For example, a 10lb bag of salt/grit with a coverage of 10,000 sq .ft . will distribute 1lb of salt/grit every 1,000 sq .ft . at full rate or 1/2lb . of
salt/grit every 1,000 sq .ft . at half rate .
6.10. For pre-calculated rates see Chart 'A' (Example: A 25lb bag with a 15,000 sq .ft . coverage requires 1 .7lb of media per 1,000 sq .ft .
6.11. use Chart 'B' to find the closest spreader setting . For example, 1 .7lb per 1000 sq .ft . = spreader setting 6)
6.12. use both charts as a guide only; experience will replace necessity to use the charts but they will be a good reference point .
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: no liability is accepted for incorrect use of this product .
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim .
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode .
01284 757500
01284 703534 sales@sealey .co .uk
Sole Uk Distributor, Sealey Group,
Kempson Way, Suffolk Business Park ,
Bury St . Edmunds, Suffolk,
IP32 7AR
www .sealey .co .uk
7. MAINTENANCE
(ChART 'B') SPREADER SETTINGS/SPREADER WIDThS
MATERIALS TO BE
USED
LBS/1000
SQ.FT
SPREADER
SETTING
SMALL PARTICLE
SPREAD
MEDIUM PARTICLE
SPREAD
LARGE PARTICLE
SPREAD
SALT
GRIT
OThER MATERIALS-:
FERTILISER
WEED
kILLER
E.T.C.
1 4 5-6 ft 6-9 ft 9-12 ft
2 6 5-6 ft 6-9 ft 9-12 ft
3 8 5-6 ft 6-9 ft 9-12 ft
4 10 5-6 ft 6-9 ft 9-12 ft
5 12 5-6 ft 6-9 ft 9-12 ft
6 14 5-6 ft 6-9 ft 9-12 ft
7 16 5-6 ft 6-9 ft 9-12 ft
8 18 5-6 ft 6-9 ft 9-12 ft
9 20 5-6 ft 6-9 ft 9-12 ft
10 23 5-6 ft 6-9 ft 9-12 ft
11 25 5-6 ft 6-9 ft 9-12 ft
Environmental Protection
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be
sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment.
When the product becomes completely unserviceable and requires disposal, drain off any fluids (if applicable)
into approved containers and dispose of the product and the fluids according to local regulations.
SSB37W Issue: 2 (A) - 26/08/14
Original Language Version
SSB37W Issue: 2 (A) - 26/08/14 © Jack Sealey limited