Imaxrc IR-GT3B - Manual (Page 7)

2.4G OPERATION NOTES
Our products are well matched in the factory ,you do not need to match
by yourself. But if you are going to match the receiver with other
transmitter, or you need to change a new receiver or transmitter, please
follow the following steps:
A. Install the battery to 2.4G transmitter and shut it down.
B. Insert the matching lines to the channel BIND/CH3 port of the receiver.
(Figure.1).
C. Connect the receiver battery to VCC port of the receiver, on the same
ੈ̓ᄊֶ̗ښѣԈҒࣃፃ᣿ᦡࠫἻ০௄ᭊϢᦡࠫүͻΧԻΎၹǍΧݠ౧০࠲ଌஆ఻ᡲԳ
ܱᄊԧ࠱఻ᤉᛡᦡࠫΎၹἻੋᏨ০᜶ఞ૱ழᄊଌஆ఻ੋᏨԧ࠱఻Ἳឰ০ોݠʾᄊ൦ᰡᤉ
ᛡὉ
ฌὉੈ̓ᄊଌஆ఻ԧ࠱ጇፒἻˀᡲХֶ߲ྡЪࠔἰ
1.࠲2.4Gԧ࠱఻ᜉݞႃ෉ἻࣳТ᫇ԧ࠱఻Ǎ
2.࠲ᦡࠫጳଣКଌஆ఻ᄊBIND/CH3ᤰ᥋ଌ԰ἷݠڏ1ἸǍ
3.࠲ଌஆ఻ႃ෉ଣКଌஆ఻ᄊVCCᤰ᥋ଌ԰Ἳ൥௑Իᄺ҂ଌஆ఻ᄊLEDښ᫅ཇἻ൥᛫ᇨଌ
ஆ఻ᤉКᦡࠫ࿄গǍ
4.࠲ԧ࠱఻ʽᄊᦡࠫ᪄(BIND)ોͱἻཀྵՑ੪नԧ࠱఻ႃູनТǍἷฌὉˀ᜶౛नો᪄ἸǍ
5.᜺ࠣଌஆ఻ʽᄊLEDἻݠ౧ԧဘLEDˀг᫅ཇ᛫ᇨᦡࠫੇҪǍἷฌὉ൥᣿ሮܸጞ௑ᫎ˞
5SࢻԿἸǍ
6.౛नԧ࠱఻ʽᄊᦡࠫો᪄Ἳપ଀ଌஆ఻ʽᄊᦡࠫጳǍ
7.࠲ͪ఩٨ᜉʽࣳᤰႃ฾តǍ
8.ݠ౧ ฾តNGἻѷ᧘ܭ̿ʽүͻǍ
9.ݠ௑฾តOK,ѷ࠲ႃູଌ݀ଣКVCCἻᦡࠫ߹ੇǍ
ฌὉ̿ʽᦡࠫவขἻ̩ᤠՌ̆*."93$ᄊ2.4Gֶ̗Ǎ Installation When A Motor Controller Is Used:
MATCHING(CODE
Receiver Connectivety
10
Battery Charging Notes
11
ࣾߕᱧ὎ಸ⮱Ⴖ㷲
Figure 1
ANT
Receiver
ڏ
Figure 1 ڏ
Receiver ଌஆ఻
Steering System
வՔጇፒ
Throttle
෴᫃
Servo
ͪ఩٨
Receiver
LED
ଌஆ఻
Match line ࠫᆊጳ
Battery
ႃ෉
time the two LED are flashing and this means the receiver are going to
the matching status.
D. Press and hold the button on the transmitter, and then switch on the
power supply.
E. Observe the LED on the receiver, if find that the LED is not flash any
more and that means successful Matched. ( This process about 5s)
F. Release the match button on the transmitter, take out the match line.
G. Install the server and then test.
H. If the test fail, please repeat the action above.
I. If the tests success ,then insert the power supply port into VCC, match
complete.( The above ways of match is only suitable for IMAXRC 2.4G
products)