Imaxrc B610-PRO - Manual (Page 11)

Warning and error messages
19 20
B6 10 Pro incorporates a various functions of protective and monitoring the system to
verify functions and the state of its electronics.In any case of occurring error,the screen
displays the cause of error that is self-explanatory with audible sound.
The output is connected to a battery with incorrect polarity.
This will be displayed in case of detecting an interruption
of the connection between battery and output or voluntarily
disconntcting the charge lead during the operation of
charge or discharge on output.
There was a short-circuit at OUTPUT.Please check the
charging leads.
The voltage of input power drops below the limit.
The voltage of Lithium battery pack was selected
incorrectly.Verify the voltage of battery pack carefully.
There happens the malfunction at the charger circuit by
any reason. The charger should be repaired at the factory.
The peocessor detects the voltage is lower than you set at
Lithium program. Please check the cell count of the battery
pack.
The peocessor detects the voltage is higher than you set
at Lithium program. Please check the cell count of the
battery pack.
The voltage of one of the cell in the Lithium battery pack is
too low. Please check the voltage of the cell one by one.
The voltage of one of the cell in the Lithium battery pack is
too high. Please check the voltage of the cell one by one.
There are bad connection at the individual
connector.Please check the connector and cables carefully.
The internal temperature of the unit goes too high. Cool
down the unit.
The processor can not continue to control the feeding
current by any reason.The unit needs to be repaired.
Glossary of terms
Glossary of terms
Amps(A): The unit of measure for charge or discharge electric current.The program of
the charger will show most of the current in amps(A) at its LCD screen.
Milli-amps(mA): The electric current,being amps(A) multiplied by 1000 and noted as
'mA'.So 2.0A is the same as 2000mA (2.0×1000).Or, to convert mA to amps,divide the
mA number by 1000.So 200mA is the same as 0.2A. If a current value is below 1.0A, the
LCD screen of the charge will still show the current in amps,not milli-amps.For
example,a current of 600mA will be displayed as 0.6A,and a current of 100mA will
actually be shown as 0.1A.
Capacity,milli-amp hours (mAh),and amp-hours(Ah): Charge energy stored by a
battery is called capacity,which is defined as how much current a battery can supply
constantly over one hour of time.Most hobby batteries are rated for capacity in 'mAh' or
milliamp hours.A 650mAh battery can deliver 650mAh of current for one hour
(650mA×1hr=650mAh).The batteries of very large capacity,such as lead-acid(Pb)
batteries,are usually rated in 'Ah' or amp-hours.A'12V 60Ah'car battery can deliver 60
amps of current for one hour (60A×1hr=60Ah).
Nominal voltage(V): The nominal voltage of the battery pack can be determined as
follows;
• Nicd or NiMH:multiply the total number of cells in the pack by 1.2.A 8-cell pack will
have a nominal voltage of 9.6 volts(8×1.2).
• LiPo:multiply the total number of cells in the pack by 3.7.A 3-cell LiPo wired in series
will have a nominal voltage of 11.1 volts(3×3.7).
• Lilo:multiply the total number of cells in the pack by 3.6.A 2-cell Lilo wired in series
will have a nominal voltage of 7.2 volts(2×3.6).
• LiFe:multiply the total number of cells in the pack by 3.6.A 2-cell Lilo wired in series
will have a nominal voltage of 13.2 volts(4×3.3).
If the nominal voltage of the bettery is not printed on the battery's label,consult your
battery manufacturer or supplier.Do not guess the rated voltage of battery.
'C'-rating: Capacity is also referred to as the 'C'-rating.Some battery suppliers
recommend charge and discharge currents based on the battery'C'rating.A
battery'1C'current is the same number as the battery's rated capacity number,but noted
in mA or amps.A 600mAh battery has a 1C current value of 600mA,and a 3C current
value of (3×600mA) 1800mA or 1.8A.The 1C current value for a 3200mAh battery would
be 3200mA(3.2A).
REVERSE POLARITY
CONNECTION BREAK
SHORT ERR
INPUT VOL ERR
VOL SELECT ERR
BREAK DOWN
BATTERY CHECK
LOW VOLTAGE
BATTERY CHECK
HIGH VOLTAGE
BATTERY VOLTAGE
CELL LOW VOL
BATTERY VOLTAGE
CELL HIGH VOL
BATTERY VOL ERR
CELL CONNECT
TEMP OVER ERR
CONTROL FAILURE