FeiYu Tech FY-G3Ultra 3-Axis Handheld Gimbal - Manual

请先安装好Gopro3相机后，再通电。
WARNING!
注意!
GoPro Hero 3 or Hero 3+ camera must be installed before
supplying power to the Gimbal. Failure to do so will result
in damage to the gimbal motors.
Battery×3
电池×3
扭开电源盖，把电池放入电池仓后，按下电源开关，即可启动3轴云台。
电源开关
Remove the power switch cap, insert the batteries into the handle as shown.
Replace the power switch cap and your G3 Ultra 3 Axis Gimbal is now ready
to use by simply pressing the power button and following the gimbal
initialization instructions below.
Power Switch Gopro3安装图
Gopro3 Installation Diagram
1
2
3
把云台放置，保持静止，然后打开电源，等待云台运行后，可以拿起云台正常工作。
1.在启动后俯仰角与水平线有小角度偏差。
2.横滚角与水平线有小角度的偏差。
3.保持航向静止时，航向角有频繁的小角度修正。
G3Ultra 三轴手持稳定云台（适用于Gopro3和Gopro3+）
4
状态指示灯说明
Indicator Explanation
云台初始化
当云台出现如下情况时需要初始化:
Initialize The FY-G3 Ultra Gimbal
3 Axis
指示灯
Indicator
Indicator
Indicator
指示灯
指示灯
状态指示灯说明
指示灯状态 说明
蓝色3次闪烁
蓝色2次闪烁
蓝色1次闪烁
蓝色快速闪烁
电池电量充足
电池电量尚可
电池电量低
电池没电，需要充电
Indicator Explanation:
LED Status Explain
Blue light flashes three times
Blue light flashes twice
Blue light flashes once
Blue light keeps flashing
Full power
Enough power
Low power
No power 用于切换云台操作模式，具体方法参见：带指示灯的按
钮功能健。
5
（通过改变指示灯闪烁来识别云台操作模式）
USB接口
USB接口
用于连接电脑升级最新的三轴手持
稳定云台固件。
Used to connect to a computer to upgrade the device
to the latest firmware.
Interface And Button
接口和按键
功能键
P C
Mode Button
Button
(Identify the operation mode via switch to different
status of the indicator light)
Used to change operating mode and subsequently
displays the current mode. See Mode Selection
Instructions below for further details.
功能健
USB Interface
USB Interface
Secure the GoPro Hero 3 or Hero 3+ camera as shown
using the included M2×22 Knurled Thumb Screw.
Keep the gimbal motionless, then power on, hold the gimbal steady and it will initialize automatically.
Once complete the camera will be level with the horizon in pitch and roll angles and it will be in Heading
Follow Mode.
1. After power on, the angle of pitch is not level with the horizon line.
2. After power on, the angle of roll is not parallel with the horizon line.
3. When the gimbal is in heading lock, the angle of heading moves frequently (heading is not stationary)
In addition to initial power on,the FY-G3 Ultra Gimbal needs to be initialized whenever the
following situations appear:
FY-G3 Ultra Gimbal Initialization Instructions:
云台初始化的方法：
M2×22 Knurled Thumb
Screw
M2×22滚花手拧螺钉
6
1. 航向跟随模式：俯仰和横滚锁定，航向随着手持的方向平滑的
转动。
2. 航向和俯仰跟随模式：横滚锁定，航向和俯仰的方向随着手持
的方向平滑的转动。
3. 锁定模式：航向、俯仰和横滚都锁定。
1. Heading Follow Mode：Camera Pitch and Roll Angles
remain constant, heading follows the handheld position.
2. Heading And Pitch Follow Mode：Camera Roll Angle
remains constant. Heading and Pitch follow the
handheld position.
3. Heading Lock Mode: Heading, Pitch and Roll are all
locked to point at one position.
Item
Double Press
Single Press
Long Press For 1 Second
Button With Indicator Light Function :
LED Status
Single Flashes
Double Flashes
On Constantly
Function Explanation
Heading follow mode
Heading and pitch follow mode
Heading,pitch and roll are all locked
动作方式
连续两次按下
单次按下
长按1秒
带指示灯的按钮功能健：
指示灯状态
单次闪烁
双次闪烁
常亮
功能说明
航向跟随模式
航向和俯仰跟随模式
锁定模式（航向、俯仰和横滚都锁定）
功能介绍
Mode Selection Instructions