Blizzard Lighting RGBAW ROCKER Panel (Rev A) - Manual (Page 6)

Page 11
ROCKER PANEL RGBAW Manual Rev. A Copyright (c) 2010 Blizzard Lighting, LLC
DMX Values In-Depth
Channel Channel Value Does...
1 000 <-> 255 Red Intensity
2 000 <-> 255 Green Intensity
3 000 <-> 255 Blue Intensity
4 000 <-> 255 Amber Intensity
5 000 <-> 255 White Intensity
6 000 <-> 255 Dimmer (0 <--> 100%)
Color Macro Speed Adjustment (When Ch. 7 is between 250 <--> 255)
7
000 <-> 009
010 <-> 019
020 <-> 029
030 <-> 039
040 <-> 049
050 <-> 059
060 <-> 069
070 <-> 079
080 <-> 089
090 <-> 099
100 <-> 109
110 <-> 119
120 <-> 129
130 <-> 139
140 <-> 149
150 <-> 159
160 <-> 179
180 <-> 189
190 <-> 199
200 <-> 209
210 <-> 219
220 <-> 229
230 <-> 239
240 <-> 249
250 <-> 255
Color Macros
No Function
Red 100%
Green 100%
Blue 100%
Amber 100%
White 100%
Yellow (RG)
Magenta (RB)
Pink (RW)
Orange (RA)
Cyan (GB)
Light Green (GW)
Green (Rosco 205)
Light Blue (BW)
Blue (Rosco 101)
Light Orange (RAW)
White (RGB)
Yellow (Rosco 603)
Magenta (Rosco 507)
White (RGBAW)
Magenta (Rosco 501)
Light Cyan
Cyan #3
White
Color Change (Channel 6 controls speed)
8 000 <-> 001
002 <-> 255
Strobe
No Function
Strobe (0 <--> 100%)
9 000 <-> 015
016 <-> 255
Color Fade
No Function
Color Fade
Page 12
ROCKER PANEL RGBAW Manual Rev. A Copyright (c) 2010 Blizzard Lighting,
LLC
Troubleshooting
Symptom Solution
Fixture Auto-
Shut Off
Check the fan in the fi xture. If it is stopped or moving
slower than normal, the unit may have shut itself off due to
high heat. This is to protect the fi xture from overheating.
Clear the fan of obstructions, or return the unit for service.
Beam is Dim Check optical system and clean excess dust/grime. Also
ensure that the 220V/110V switch is in the correct position,
if applicable.
No Light Output Check to ensure fi xture is operating under correct mode, IE
sound active/auto/DMX/Etc., if applicable. Contact service
for more information.
Chase Speed
Too Fast/Slow
Check to ensure proper setup of speed adjustment.
No Power Check fuse, AC cord and circuit for malfunction.
Blown Fuse Check AC cord and circuit for damage, verify that moving
parts are not restricted and that unit’s ventilation is not
obstructed
Slow Movement Verify that 220V/110V switch is in the correct position, if
applicable. Also check that speed channels are set appropri-
ately.
No Response to
Audio
Verify that the fi xture is in “Sound Active” mode.
Adjust Audio Sensitivity, If Applicable.
Fixture Not
Responding /
Responding Er-
raticly
Make sure all connectors are seated properly and securely.
Use Only DMX Cables.
Install a Terminator.
Check all cables for defects.
Reset fi xture(s).
Intermittant
Lamp
Check lamp for properly installation.
Relamp, lamp may have reached end of life.
Remote Doesn’t
Work
Verify remote control cable is installed properly and securely.
Verify remote is correct type (CA-9 or other as applicable.)
Fixture Moving
On Its Own
Verify proper mode of operation. Is the fi xture in “Auto”
mode?
If your problem isn’t listed, or if problems persist,
please contact support: [email protected].