Black & Decker Fire Storm FS2200QS - Manual (Page 2)

Sanding
Lead based paint
Sanding of lead based paint is NOT RECOMMENDED due to the difficulty of controlling the
contaminated dust. The greatest danger of lead poisoning is to children and pregnant
women.
Since it is difficult to identify whether or not a paint contains lead without a chemical
analysis, we recommend the following precautions when sanding any paint:
Personal safety
• No children or pregnant women should enter the work area where the paint sanding is
being done until all clean up is completed.
• A dust mask or respirator should be worn by all persons entering the work area. The filter
should be replaced daily or whenever the wearer has difficulty breathing.
NOTE: Only those dust masks suitable for working with lead paint dust and fumes should
be used. Ordinary painting masks do not offer this protection. See your local hardware
dealer for the proper (NIOSH approved) mask.
• NO EATING, DRINKING or SMOKING should be done in the work area to prevent
ingesting contaminated paint particles. Workers should wash and clean up BEFORE
eating, drinking or smoking. Articles of food, drink, or smoking should not be left in the work
area where dust would settle on them.
Environmental safety
• Paint should be removed in such a manner as to minimize the amount of dust generated.
• Areas where paint removal is occurring should be sealed with plastic sheeting of 4 mils
thickness.
• Sanding should be done in a manner to reduce tracking of paint dust outside the work
area.
Cleaning and disposal
• All surfaces in the work area should be vacuumed and thoroughly cleaned daily for the
duration of the sanding project. Vacuum filter bags should be changed frequently.
• Plastic drop cloths should be gathered up and disposed of along with any dust chips or
other removal debris. They should be placed in sealed refuse receptacles and disposed of
through regular trash pick-up procedures. During clean up, children and pregnant women
should be kept away from the immediate work area.
• All toys, washable furniture and utensils used by children should be washed thoroughly
before being used again.
ASSEMBLY
WARNING: To reduce the risk of injury, make sure that the tool is switched off and
unplugged before performing any of the following assembly.
Fitting sanding sheets (fig. B )
• Soften the sanding sheet by rubbing its non-abrasive side over the edge of a work table.
• Press the paper clamp levers (6) upwards to release them from the retaining grooves and
open the paper clamps by pressing them down.
• Place the sheet onto the sanding base.
• Insert the edge of the sanding sheet into the front paper clamp as shown.
• Press the front paper clamp lever (6) downwards and locate it in the retaining groove.
• While keeping a slight tension on the sheet, insert the rear edge of the sheet into the rear
paper clamp.
• Press the rear paper clamp lever (6) downwards and locate it in the retaining groove.
Punching sanding sheets (fig. C)
The paper punch (7) is used for punching dust extraction holes in sanding sheets without
pre-punched holes.
Fit a sanding sheet.
• Hold the tool in position right above the paper punch (7).
• Press the tool with the sanding base (5) down into the paper punch.
• Take the tool off the paper punch (7) and check whether the holes in the sanding sheet
have been fully pierced.
Fitting and removing the dust canister (fig. D)
• Fit the dust canister (3) over the dust extraction outlet (4).
• To remove the dust canister (3), pull the dust canister to the rear and off the outlet (4).
OPERATION
WARNING: To reduce the risk of injury, let the tool work at its own pace. Do not
overload.
Switching on and off (fig. E)
• To switch the tool on, press the part of the on/off switch (1) marked 'I'.
• To switch the tool off, press the part of the on/off switch (1) marked '0'.
Emptying the dust canister (fig. D)
• The dust canister should be emptied every 10 minutes.
• Pull the dust canister (3) to the rear and off the tool .
• Remove the cover (2) by twisting it counterclockwise.
• Hold dust canister with the filter (8) facing down and shake the canister (3) to empty the
contents.
• Shake the cover (2) to empty the contents.
• Refit the cover (2) onto the dust canister (3), twisting it clockwise until it locks into place.
• Fit the dust canister (3) onto the tool.
Cleaning the dust canister filter
Warning: To reduce the risk of personal injury, do not use compressed air to clean the
filter.
NOTE: Do not use a brush or sharp objects to clean the filter as these items can reduce
the durability of the filter material. Do not wash the filter.
• The dust canister filter (8) is re-usable and should be cleaned regularly.
• Empty the dust canister (3) as described above.
• Pull the dust canister filter (8) off the dust canister (3).
• Shake off the excess dust by tapping the filter (8) into a trash can.
• Replace the dust canister filter (8).
• Fit the cover (2).
• Fit the dust canister (3) onto the tool.
Hints for optimum use
• Do not place your hands over the ventilation slots.
• Do not exert too much pressure on the tool.
• Regularly check the condition of the sanding sheet. Replace when necessary.
• Always sand with the grain of the wood.
• When sanding new layers of paint before applying another layer, use extra fine grit.
• On very uneven surfaces, or when removing layers of paint, start with a coarse grit. On
other surfaces, start with a medium grit. In both cases, gradually change to a fine grit for a
smooth finish.
Dust Collection
WARNING: Fire hazard. Collected sanding dust from sanding surface coatings
(polyurethane, linseed oil, etc.) can self-ignite in sander dust canister or elsewhere and cause
fire. To reduce risk, empty canister frequently and strictly follow sander manual and coating
manufacturer's instructions.
WARNING: Fire hazard. When working on metal surfaces, do not use the dust canister or
a vacuum cleaner because sparks are generated. Wear safety glasses and a dustmask. Due
to the danger of fire, do not use your sander to sand magnesium surfaces. Do not use for wet
sanding.
TROUBLESHOOTING
Problem Possible Cause Possible Solution
• Unit will not start. • Cord not plugged in. • Plug tool into a working
outlet.
• Circuit fuse is blown. • Replace circuit fuse.
(If the product repeatedly
causes the circuit fuse to
blow, discontinue use
immediately and have it
serviced at a Black & Decker
service center or authorized
servicer.)
• Circuit breaker is tripped. • Reset circuit breaker.
(If the product repeatedly
causes the circuit breaker to
trip, discontinue use
immediately and have it
serviced at a Black & Decker
service center or authorized
servicer.)
• Cord or switch is damaged. • Have cord or switch
replaced at Black & Decker
Service Center or Authorized
Servicer.
For assistance with your product, visit our website www.blackanddecker.com for the loca-
tion of the service center nearest you or call the BLACK & DECKER help line at
1-800-544-6986.
Maintenance
Your tool has been designed to operate over a long period of time with a minimum of
maintenance.
Continuous satisfactory operation depends upon proper tool care and regular cleaning.
• Clear the cooling vents and slots with a clean, dry paint brush.
• Clean the housing with a clean, damp cloth. Do not use solvents.
Accessories
Recommended accessories for use with your tool are available at extra cost from your local
dealer or authorized service center. If you need assistance in locating any accessory for your
tool, please call 1-800-544-6986.
WARNING: The use of any accessory not recommended for use with this tool could be
hazardous.
Service Information
All Black & Decker Service Centers are staffed with trained personnel to provide customers
with efficient and reliable power tool service. Whether you need technical advice, repair, or
genuine factory replacement parts, contact the Black & Decker location nearest you. To find
your local service location, refer to the yellow page directory under "Tools—Electric" or call:
1-800-544-6986 or visit www.blackanddecker.com
Full Two-Year Home Use Warranty
Black & Decker (U.S.) Inc. warrants this product for two years against any defects in material
or workmanship. The defective product will be replaced or repaired at no charge in either of
two ways.
The first, which will result in exchanges only, is to return the product to the retailer from whom
it was purchased (provided that the store is a participating retailer). Returns should be made
within the time period of the retailer’s policy for exchanges (usually 30 to 90 days after the
sale). Proof of purchase may be required. Please check with the retailer for their specific
return policy regarding returns that are beyond the time set for exchanges.
The second option is to take or send the product (prepaid) to a Black & Decker owned or
authorized Service Center for repair or replacement at our option. Proof of purchase may be
required. Black & Decker owned and authorized Service Centers are listed under "Tools-
Electric" in the yellow pages of the phone directory and available on our website
www.blackanddecker.com.
This warranty does not apply to accessories. This warranty gives you specific legal rights and
you may have other rights which vary from state to state. Should you have any questions,
contact the manager of your nearest Black & Decker Service Center. This product is not
intended for commercial use.
Free warning label replacement: If your warning labels become illegible or are missing, call
1-800-544-6986 for a free replacement.
Special Warranty Note to Contractors:
FIRESTORM TM branded products are offered as high end consumer home use tools and
carry a HOME USE WARRANTY. These tools are designed, manufactured and tested to
meet or exceed the needs of the do-it-yourselfer in the execution of projects and repairs in
and around the home. With proper use they will provide the home owner with step up power
and performance well beyond their two year warranty. However, if you use tools for a living
and use FIRESTORM
TM branded products or any of Black & Decker’s other Consumer
Home Use tools ON THE JOBSITE you should know that they CANNOT BE COVERED
UNDER OUR WARRANTY.
See ‘Tools-Electric’
– Yellow Pages –
for Service & Sales
Black & Decker (U.S.) Inc.,
701 E. Joppa Rd.
Towson, MD 21286 U.S.A.
E
1