Boss Audio Systems Boss Loop Station RC-300 - Manual (Page 23)

Phrase Memory Settings
23
O
ver
vie
w
Basic O
per
ation
Sa
ving
Track
Rh
ythm
LOOP FX
Sy
st
em S
ettings
USB
MIDI
A
ppendix
Phr
ase M
emor
y
Assigning the Function of Pedals and External Controllers (Assign)
For each phrase memory, you can assign the function of the RC-300’s pedals and any connected external pedals (EXP
pedals, foot switches: p. 24). You can also make assignments for control change messages received from an external MIDI
device (e.g., FC-300).
For each phrase memory, you can create eight different assignments (assignment numbers 1–8), which specify the
parameter controlled by each controller.
Parameter Value Explanation
Assign1 Switch
ON
Enabling Assignments 1–8 (Assign Switch)
Here you can specify whether assignments will be used.
OFF The assignment will not be used.
ON The assignment will be used.
Assign1 Target
EFFECT CONTROL
Specifying the Assignment Target (Assign Target)
Here you can choose the Assignment Target. In addition to the following assignment targets, you can also specify
a track, rhythm, or a LOOP FX parameter as the assignment target. For details on the parameters, refer to the
explanation of each parameter in this manual.
* Some parameters cannot be controlled during performance.
MEM Tempo(TAP)
By pressing the pedal several times in succession, the phrase memory tempo can be set so
it matches the timing you’ve used when pressing the pedal.
EFFECT CONTROL Applies an effect suitable for the selected LOOP FX type.
MEMORY INC
Switches the phrase memory.
MEMORY DEC
LOOP FX ON/OFF Switches the LOOP FX on/off.
FX TYPE INC
Switches the LOOP FX type.
FX TYPE DEC
UNDO/REDO Allows you to undo/redo the last recording or overdubbing of a track (p. 12).
TR1–3 UNDO/REDO Allows you to undo/redo a specific track (p. 12).
TR1–3 PLAY/STOP Allows you to play/stop a specific track.
ALL PLAY/STOP Allows you to simultaneously play/stop all tracks.
TRACK1–3 CLEAR Clears the track (p. 12).
INPUT MASTER LEV Adjusts the input level from the INPUT (AUX, INST, MIC) jacks.
INPUT MIC SWITCH Switches the INPUT MIC jack input on/off.
CC#1–#31, CC#64–#95 Transmits the control change message specified here from the MIDI OUT connector.
Assign1TargetMin
0
Assign1TargetMax
100
Specifying the Target Range (Target Range)
Here you can specify the range in which the parameter can be controlled. The value will depend on the parameter
that’s assigned as the Target (Assign Target).
Assign1 Source
EXP1 PEDAL
Specifying the Controller (Assign Source)
Here you can specify the controller (source) that will control the target.
EXP1 PEDAL The RC-300’s [EXP 1] pedal
LOOP FX PEDAL
The RC-300’s [LOOP FX] pedal
* The [LOOP FX] pedal switches the LOOP FX on/off. If you don’t want to use the [LOOP
FX] pedal to switch the LOOP FX on/off, choose “ASSIGN” as the setting of “Specifying the
Operation of the [LOOP FX] Pedal” (p. 32).
CTL1–4 PEDAL A foot switch 1–4 connected to the CTL/EXP jacks (p. 24)
EXP2–3 PEDAL An EXP pedal 2–3 connected to the CTL/EXP jacks (p. 24)
TRACK1–3 REC/DUB The beginning of recording/overdubbing triggered by the track 1–3 [REC/DUB/PLAY] pedal
TRACK1–3 PLAY The beginning of playback triggered by the track 1–3 [REC/DUB/PLAY] pedal
SYNC START/STOP ALL START/STOP messages from the master RC-300 unit (p. 39).
CC#1–#31, CC#64–#95 Control change messages (1–31, 64–95) from an external MIDI device