beautypg.com

Yamaha 1009MWTO-F0 User Manual

Page 57

background image

R

ef

er

ences

Error Messages

DME64N/DME24N Owner’s Manual

57

Download Success

The program has been successfully updated.

Downloading
Do not turn off

Program update in progress. Do NOT turn power off
while the unit displays this message.

DSP Power Shortage

Audio is not input or output and is muted due to
insufficient DSP resources.

This error sometimes occurs if you try to operate a
configuration at 96 kHz that has been created with a
word clock of 48 kHz. To operate a configuration at any
word clock setting, use DME Designer to create a
configuration with the word clock set to 96 kHz.

Duplicate IP Adr.

Duplicate IP addresses.

Change the IP addresses so that there are no duplicates.

Err: Wrong Device
Group Settings

The device group configuration set via DME Designer
does not match the actual configuration.

Use DME Designer to go off-line, create a configuration
that correctly matches the actual configuration, and then
go back on-line to synchronize the configuration.

Executing

A User Defined Button operation is in progress.

File Opening
Do not turn off

A file operation is in progress during which the computer
manipulates scene data. Do NOT turn power off while the
unit displays this message.

Illegal MAC Adr.

An illegal MAC address has been encountered.

This could be due to a hardware malfunction. Refer this
problem to a contact a Yamaha dealer.

Invalid IP Adr.

The network IP address is not appropriate.

Set an appropriate network IP address.

Network Busy

There is too much network traffic. Communication is not
possible.

Check the devices connected to the network. If there are
too many devices connected, reduce the number of
devices.

Network Error

One of the following errors has occurred on the network:
• A cable has been unplugged.
• The power to a network switch or router has been shut off.
• A cable is in an inappropriate state (e.g. a heavy object

has been placed on the cable, etc.). Static electricity
can also cause errors.

Locate and eliminate the cause of the error.

Network Setup

Preparing network connection.

No Current Scene

There is no data in the current scene.

Send appropriate scene data from a computer running
the DME Designer application.

No MAC Adr.

MAC address not specified.

This could be due to a hardware malfunction. Refer this
problem to a Yamaha dealer.

Panel Locked

Panel operation not allowed.

Press the [CANCEL] button for longer than 2 seconds to
disengage panel lock and allow panel operation.

Panel Unlocked

Panel lock has been disengaged. Panel operation is now
possible.

Recovering
Do not turn off

A program update attempt has failed, and the previous
program is currently being restored.

Do NOT turn power off while the unit is displaying this
message. If the update attempt repeatedly fails, there
may be a hardware malfunction. Refer this problem to a
Yamaha dealer.

Saving HA Info
Do not turn off

Head amplifier info save in progress.
(Do not turn power off.)

Saving Setup Info
Do not turn off

Info set up via the Utility display (other than head
amplifier info) is being saved.
(Do not turn power off.)

Scene Recalling
Do not turn off

Scene recall in progress. Do NOT turn power off while the
unit displays this message.

Scene Storing
Do not turn off

Scene store in progress. Do NOT turn power off while the
unit displays this message.

Searching for Master
DME Unit...

Currently searching for the master DME unit.

Searching for Slave
DME Unit...

Currently searching for the slave DME unit.

SLOT1 Sync Err

The DME64N/24N clock is not synchronized with the
clock of the card installed in I/O slot 1.

Make sure that the DME64N/24N and the card or external
source supplying the word clock are set to use the same
word clock.

SLOT2 Sync Err

The DME64N clock is not synchronized with the clock of
the card installed in I/O slot 2.

Make sure that the DME64N and the card or external
source supplying the word clock are set to use the same
word clock.

SLOT3 Sync Err

The DME64N clock is not synchronized with the clock of
the card installed in I/O slot 3.

Make sure that the DME64N and the card or external
source supplying the word clock are set to use the same
word clock.

SLOT4 Sync Err

The DME64N clock is not synchronized with the clock of
the card installed in I/O slot 4.

Make sure that the DME64N and the card or external
source supplying the word clock are set to use the same
word clock.

Message

Meaning

Action