Panasonic DMR-E80H - Manual (Page 7)

7
RQT6984
Se
tt
ing up
Preparation
≥ Confirm that the antenna is connected correctly.
≥ Turn on the television and select the appropriate video input to
suit the connections to this unit.
1
Press [ Í , DVD POWER] to turn the
unit on.
2
Press [ 3 , 4 ] to select the menu lan-
guage and press [ENTER].
e.g., when you select
English
3
Press [ENTER].
Plug-in Auto Tuning starts and the unit puts the stations it
can receive into channels.
The unit then proceeds with Auto Clock Setting. The time is
displayed when finished. If the clock is an hour slower or
faster than the actual time, go to “Time Zone Adjust” to cor-
rect it (
➜ page 47).
4
When the display shows the correct time
Press [ENTER] to complete Plug-in
Auto Tuning.
If the unit couldn’t set the clock automatically
Press [ENTER] to show the “Manual Clock Setting” screen. Set the
time manually (
➜ page 47).
To start Plug-in Auto Tuning again (after reloca-
tion, for example)
When the unit is on and stopped
1 Press and hold [ X , CH] and [ W , CH] on the main unit for
about five seconds.
The unit turns off.
2 Press [ Í , DVD POWER] to turn the unit on.
Follow the above steps 2–4.
1
Press [SETUP] to show the menus.
2
Press [ 3 , 4 ] to select “Channel” and
press [ 1 ].
3
Press [ 3 , 4 ] to select “Antenna Sys-
tem” and press [ENTER].
4
Press [ 3 , 4 ] to select “TV” or
“CATV” and press [ENTER].
The screen shown in step 2 reappears.
5
Press [ 3 , 4 ] to select “Auto Channel
Setting” and press [ENTER].
If you have not yet set clock, the “Auto Channel/Clock Set-
ting” screen appears.
6
Press [ENTER].
Auto setting starts. This takes a few minutes. (To stop auto
channel setting, press [RETURN].) When finished, the Com-
plete screen or time display is shown. Press [ENTER].
To return to the previous screen
Press [RETURN].
When you are finished
Press [SETUP].
Add or delete channels if necessary channels are not set or unnec-
essary channels are set.
While this unit is receiving the antenna signal (but not during
recording):
1
Press the numbered buttons to select
a channel.
e.g., “5”: [0] ➜ [5]
“15”: [1] ➜ [5]
“115”: [100] ➜ [1] ➜ [5]
≥ You can also use [ W , X , CH]
when you are going to delete a channel.
2
Press [ADD/DLT].
The channel is deleted if it was set or added if it was not set.
e.g.,
Repeat steps 1 and 2 as necessary.
Antenna system, channel caption, and VCR Plus r guide
channel settings all revert to the default values when you
perform the procedure below. Timer recording settings are
also cleared.
If Plug-in Auto Tuning fails
English
Español
Français
Press ENTER
Pulse ENTER
Appuyer sur ENTER
Select Language
Seleccione la Lengua
Sélection de Langue
RETURN
ENTER
Auto Channel/Clock Setting
Connect antenna cable and if you use a
cable box, tune it to your local PBS CH
then. . .
Please push the ENTER key.
TAB SELECT
Antenna System
Auto Channel Setting
Channel Caption
Preset Channel Caption
Manual Channel Caption
VCR Plus i CH Setting
CATV
Channel
SETUP
RETURN
Set Up
Disc
Video
Audio
Display
TV Screen
Adding and deleting channels
Antenna System
Auto Channel Setting
Channel Caption
Preset Channel Caption
Manual Channel Caption
CATV
Set Up
Disc
Channel
SETUP
SETUP
Set Up
Channel
Antenna System
TV
CATV
SETUP
Set Up
Disc
Video
Audio
Display
Channel
Auto Channel Setting
Connect antenna cable and if you use a
cable box, tune it to your local PBS CH
then...
Please push the ENTER key.
Unit’s display
CHANNEL 15 DELETED