Panasonic AJ-SD965P - Manual (Page 14)

14
Front panel
Parts and their functions
(continued)
\ ENC CONTROL switch
REMOTE:
Set to this position to adjust the video output
signals using a device which has been connected
to the 9-pin REMOTE, RS-232C or PARALLEL
connector.
LOCAL:
Set to this position to adjust the video output
signals using the unit’s controls (], ^, _, `).
] VIDEO LEVEL control and switch
These are used to adjust the video output level.
When the ENC CONTROL switch
\ is set to
LOCAL and the VIDEO LEVEL switch is set to
MANUAL, the video output level can be adjusted
using the VIDEO LEVEL control.
The maximum adjustment range is ±3 dB.
When the VIDEO LEVEL switch is set to PRESET,
the video output level is fixed at 0 dB.
^ CHROMA LEVEL control and switch
These are used to adjust the chroma level.
When the ENC CONTROL switch
\ is set to
LOCAL and the CHROMA LEVEL switch is set to
MANUAL, the chroma level can be adjusted using
the CHROMA LEVEL control.
The maximum adjustment range is ±3 dB.
When the CHROMA LEVEL switch is set to
PRESET, the chroma level is fixed at 0 dB.
_ SET UP (BLK) control and switch
These are used to adjust the setup (black) level.
When the ENC CONTROL switch
\ is set to
LOCAL and the SET UP switch is set to MANUAL,
the setup level can be adjusted using the SET UP
control.
The maximum adjustment range is ±14 IRE
(100 mV).
When the SET UP switch is set to PRESET, the
setup (black) level is fixed at 0 IRE (0 mV).
` HUE (CHROMA PH) control and switch
These are used to adjust the hue (chroma phase).
When the ENC CONTROL switch
\ is set to
LOCAL and the HUE switch is set to MANUAL, the
hue can be adjusted using the HUE control.
The maximum adjustment range is ±30 degrees.
When the HUE switch is set to PRESET, the hue
(chroma phase) is fixed at 0 degree.
a TC (REGEN/PRESET) switch
REGEN:
The internal time code generator is synchronized
with the time code which the time code reader
has read from the tape.
The signal that is to be used for regeneration is
selected using setup menu No. 503 (TCG
REGEN).
PRESET:
The time code generator can be preset on the
operation panel or by remote control.
b TC (REC RUN/FREE RUN) switch
This sets the operation mode which is to make the
internal time code generator advance.
REC RUN:
The internal time code generator is advanced
during recording.
The time code advances all the time when the TC
(REGEN/PRESET) switch a is at the REGEN
position.
FREE RUN:
When the power is on, the internal time code
generator is advanced regardless of the operation
mode.
ON POWER
REMOTE SUPER REC INH TCG MODE
ON
OFF
DVCPRO 50
EJECT
SEARCH TC CUE VIDEO ASSEM COUNTER
CH 1 CH 2 CH 3 CH 4
PF 1 PF 2 PF 3 PF 4
RESET
PLAYER RECORDER SET
TC PRESET MENU PF
STAND BY
EDIT
A OUT
OUT IN SET
A IN PREROLL AUTO EDIT PREVIEW/ REVIEW INPUT SELECT METER
AUDIO MON SEL AUDIO MIX HEADPHONES
AUDIO VOL SEL
VIDEO
CH 1
ENC VIDEO
LEVEL CONTROL
REMOTE PRESET
MANUAL LOCAL
R MIX
1&2
CH1/3
PULL
CH2/4 REC CH1/3
CH1/3 CH2/4 REC CH2/4
3&4
L CH 2 CH 3 CH 4
AUDIO FULL/FINE
REC PLAY
REW FF SHIFT
PULL
STOP
INSERT
PUSH
DVCPRO
DV
2 X
OFF
REC
PB
UNITY
VAR
ON
OFF
INT
EXT
TAPE
EE
XL/L/M-cassette
SHTL
JOG
SLOW
CHROMA LEVEL PRESET
MANUAL
SET UP BLK PRESET
MANUAL
PRESET REGEN
PRESET
REC RUN
FREE RUN MANUAL
HUE TC DIAG CHROMA PH
\ a
] ^ _ ` b