Shure UP4 - Manual (Page 15)

ENGLISH ENGLISH
– 13 –
OPERATING THE UP SYSTEM WITH UC1 OR U1 BODY–PACK
1. If the UP4 receiver has not been mounted to the camera, attach the mounting box (See Attaching Mounting Box) and install the UP4 receiver,
connecting the XLR output on the receiver to the sound input on the camera (See Installing UP4 Receiver). Set the Push-Lock Audio Gain Pot
to the appropriate level for the camera sound input or other equipment you are using. If internal 9V battery power is not being used, attach the
locking dc jack to an external dc source.
2. Clip the body-pack transmitter to your belt or waistband.
3. Connect the lavalier microphone or headset microphone the transmitter.
NOTE: If you are using a headset microphone, the audio gain of the transmitter may need to be adjusted. See ADJUSTING THE AUDIO GAIN
section for details.
4. Clip the lavalier microphone to your tie, lapel, or other garment. For best results, the microphone should be 15 to 20 cm (6 to 8 in.) below your chin.
5. Slide the transmitter ON/OFF switch to the ON position. Check battery status (see Checking Battery Status).
6. On the UP4 receiver, move the power switch to the ON position. The receiver PWR LED should glow green. If you are using internal 9V battery
power and the PWR LED glows red, change the battery.
7. Make sure the transmitter and receiver are tuned to the same Group and Channel. If necessary, change the settings on either the transmitter or
receiver. See Changing Group/Channel Settings.
8. Begin speaking. The RF and AUD LEDs on the receiver should glow green, with the AUD LED flashing red at the loudest sounds.
NOTE: If the AUD LED on the receiver does not flicker red during the loudest sounds, or if it is consistently red, the transmitter gain may need to be
increased or decreased. Refer to the Adjusting the Transmitter Gain Level section. If the system still does not operate properly, consult the Trou-
bleshooting table included in this manual.
9. When the shoot is over, slide the transmitter and receiver ON/OFF switches to the OFF position to conserve battery power.
LAVALIER
MIC
OPERATING THE BODY–PACK SYSTEM
FIGURE 26
OPERATING THE UP SYSTEM WITH A UC2 OR U2 HAND-HELD TRANSMITTER
1. If the UP4 receiver has not been mounted to the camera, attach the mounting box (See Attaching Mounting Box) and install the UP4 receiver,
connecting the XLR output on the receiver to the sound input on the camera (See Installing UP4 Receiver). Set the Push-Lock Audio Gain Pot
to the appropriate level for the camera sound input or other equipment you are using. If internal 9V battery power is not being used, attach the
locking dc jack to an external dc source.
2. Slide the transmitter power ON/OFF switch to the ON position. Check battery status (see Checking Battery Status).
3. On the UP4 receiver, move the power switch to the ON position. The receiver PWR LED should glow green. If you are using internal 9V battery
power and the PWR LED glows red, change the battery.
4. Make sure the transmitter and receiver are tuned to the same Group and Channel. If necessary, change the settings on either the transmitter or
receiver. See Changing Group/Channel Settings.
5. Begin speaking. The RF and AUD LEDs on the receiver should glow green, with the AUD LED flashing red at the loudest sounds.
NOTE: If the AUD LED on the receiver does not flicker red during the loudest sounds, or if it is consistently red, the transmitter gain may need to be
increased or decreased. Refer to the Adjusting the Transmitter Gain Level section. If the system still does not operate properly, consult the “Trou-
bleshooting” table included in this manual.
6. When the shoot is over, slide the transmitter and receiver ON/OFF switches to the OFF position to conserve battery power.
OPERATING THE HAND–HELD SYSTEM
FIGURE 27