Honeywell VCC-600N/P - Manual

Operation Manual
VCC VCC - - 600N/P 600N/P
※ Thank you for choosing Honeywell VCC-600N/P camera.
Please read these instructions carefully before operating this unit,
and retain this manual for future reference.
If you have any problems with this camera, contact your local
supplier to service.
OSD Color Camera
The contents of the package
Check the below contents
- VCC-600N/P Camera 1set
- Auto Iris Lens Plug
- L Type Wrench
- Operation Manual (English)
Printed in Korea
D-100073-001, REV.0
Honeywell Security Group
Honeywell Co., Ltd.
Address: 5F, Sangam IT Tower, B4 - 4block, 1590
Sangam-dong, Mapo-gu, Seoul 121-835, Republic of
Korea
TEL: +82 2 799 6020 / 6395 / 6006
FAX: +82 2 792 9011
E-mail: [email protected]
UP BUTTON
+ - MD
VIDEO
LENS
DC12V
POWER
ENTER
DC VSD
CONT
ENTER BUTTON
(-) BUTTON
(+) BUTTON
DOWN BUTTON
LENS CONNECTOR
VIDEO OUTPUT
Lens Type Select Switch
POWER ON LED
Power Input Terminal and MD Alarm Output
1. Water and Moisture
To prevent fire or shock hazard, do not expose this camera
to rain or moisture.
2. Servicing
Do not attempt to disassemble or repair by yourself.
You may be exposed to dangerous voltage or other hazards.
Note that all servicing is qualified service personnel.
Modifications not approved by manufacturer could
void the user's authority to operate the equipment.
3. Power Sources
To prevent electric shocks and risk of hazards, do NOT use
more than the specified power source.
4. Environment
Do not install too warm or too cold place. Recommended
operation temperature is between -5℃ and 50℃
5. Sunlight
Do not point the camera at the sun. CCD can be damaged.
6. Heavy Shock and Vibration
Do not drop the camera or subject it to heavy shock of
vibration.
7. Install on an Unstable Place
Do not place or install this camera on an unstable place,
stand, tripod, bracket or table. That may cause serious injury
to people or damage to appliance
.
CAUTION for SAFETY OPERATION
8. When operation is incorrect or a malfunction is observed
While operating, if any abnormal condition (strange sound,
smell or smoke) or a malfunction (no pictures, etc.) is
observed, stop using the camera immediately, turn the
power off, then contact your supplier.
9. Cleaning
Turn the power off and wipe off the dirt with a dry soft
cloth. If it is extremely dirty, use furniture cleaner to wipe it
off. To clean the lens, use a blower or lens cleaning
tissue. (available from any camera dealer)
10. Do not shoot any source of bright light.
If the objects contain very bright areas, bright vertical or
horizontal lines may appear on the screen. This is called
"smear" , a Phenomenon which often occurs with solid
- state pickups, and is not a malfunction.
11. Damage Requiring service
Unplug the camera from the power source and refer
servicing to qualified service personnel under the following
condition:
A. If the power-supply cord or plug is damaged.
B. If the camera has been exposed to rain or water.
C. If liquid has been spilled, or objects have fallen into the camera.
D. If the camera does not operate normally by following the operating
instructions. Adjust only those controls that are covered by the
operating instructions as an improper adjustment of other controls
may result in damage and will often require extensive work by a
qualified technician to restore the camera to its normal operation.
E. If the camera has been dropped or the cabinet has been damaged.
F . If the camera exhibits a distinct change in performance.
G. Warranty is not covered in case of natural disaster or wrong
Installation.
INSTRALLATION
Mounting a lens
1. Remove the Protective cap in front of the camera.
2. Confirm the mount ring whether it is for C or CS.
3. Attach the lens to the lens mount ring.
4. If the lens has an Auto Iris mechanism, connect the iris cable to the
LENS in rear of the camera.
① In the case of having no iris amplifier : Set the slide switch to
DC (Down side).
② In the case of having iris amplifier : Set the slide switch VSD
(Upper side)
※ When connecting Auto iris lens, be sure to use the connector to
be recommended by manufacturer.( E4-191, ChuoMusen, Japan)
VSD LENS PIN CONFIGURATION
1 2
3 4
1. Power(12V) 2. No Connection
3. Video Signal 4. GND
①③
④ ②
DC IRIS LENS PIN CONFIGURATION
1 2
3 4
1. Control - 2. Control +
3. Drive + 4. Drive -
①③
④ ②
Back focus adjustment
1. In case of fixed focus lens
① Loosen the locking ring with L type wrench and set the focus ring
of lens to infinity ( ∞ ).
② Tune the mount ring to get a clear picture( distance from camera
to object is more than 23m) and fasten the locking ring.
2. In case of zoom lens
① Loosen the locking ring with L type wrench and set the lens to the
maximum telephoto position. Then turn the focus ring to focus.
※ In the case of Auto iris lens only, shoot a comparatively dark
object or reduce the ambient light so that the aperture is fully open.
② Set the lens to its maximum wide angle position, and set the focus.
③ Repeat step ① and ②, until the difference between focusing
position ① and ② is smallest.
④ When the best focusing point in found, fasten the locking ring.
Connection of power supply
Must be checked the power source from the external power supply
before power on.
TROUBLESHOOTING
DIMENSIONS
+ - MD
VIDEO
LENS
DC12V
PO WER
E NTER
D C VSD
CO NT
+ - MD
VIDEO
LENS
DC12V
PO WER
E NTER
D C VSD
CO NT
Unit: mm
Before sending the camera out for repair, check the items
below. If the problem persists after checking these items,
contact your service center.
In case of no image
Is the coaxial cable attached securely?
Are the power and voltage normal?
Has the iris of the lens inside the camera been adjusted correctly?
In case of unclear image
Is the lens in focus?
Is the lens dirty?
Is the monitor adjusted correctly?
※ Dirt of fingerprints on the lens can adversely affect the
images. Gently wipe any dirt or fingerprints off the lens
with a soft cloth or lens cleaning paper and cleaning
fluid (commercially available).
NAMES & FUNCTIONS OSD MENU
GENERAL SETUP
SYNC SYNC LEVEL adjustment (0 1…255)
BURST BURST LEVEL adjustment (0 1…255)
CONTRAST CONTRAST LEVEL adjustment
(0 1…100)
RETURN Return to the previous menu.
CAMERA SETUP
AE MODE LENS MODE, SHUTTER, AGC, BRIGHTNESS, MAX AGC,
MAX FIELDS, etc.
WB MODE AWC LOCK, AWC AUTO, ATW, INDOOR, OUTDOOR,
MANUAL, etc.
BLC MODE OFF, BLC, WDR, BMB and
their level, area setting.
PZM SET Privacy Zone Masking function setting.
NIGHTSHOT Day  Night, Night  Day mode setting.
CAMERA ID Camera ID and Position setting.
RETURN Return to the previous menu.
MEM FUNC. SETUP
DNR MODE Digital Noise Reduction mode
setting. (OFF LOWHIGH)
PIP MODE Picture-in-picture mode setting.
QUAD MODE Quad display mode setting.
MD MODE Motion Detection mode setting.
D.ZOOM Digital Zoom setting. (OFF 1.0x…16.0x)
MIRROR Mirror mode setting. (OFF H.MIRRORV.MIRRORFLIP)
RETURN Return to the previous menu.
SPECIAL SETUP
SHARPNESS Sharpness compensation setting. (0~15)
GAMMA Gamma compensation setting. (0.36~1/USER , 8steps)
LANGUAGE OSD Language setting. (ENG, KOR, JPN, CHI1, CHI2)
RETURN Return to the previous menu.
DEFAULT SETUP
FACTORY DEFAULT Set to the Factory Default.
RETURN Return to the previous menu.
EXIT SETUP
SAVE AND EXIT
EXIT
RETURN
Return to the previous menu.
This LED is ON
in power ON state.
Composite Video
Signal Output
DC Lens: with no iris amp.
VSD Lens: with iris amp.
SPECIFICATIONS
Operational
Image Sensor
Total Pixel
Effective Pixel
Scanning System
Scanning Frequency
Sync System
S/N Ratio
Min. illumination
Horizontal Resolution
Video Output
Lens Iris Control
Electronic Shutter
AGC
Back Light Compensation
White Balance
Electrical
Rated Voltage
Power Consumption
Mechanical & Environmental
Lens Mount
Weight
Dimensions
Front & Rear Color
Body Color
Operating Temp.
Storage Temp.
Operating Humidity
SONY 1/3” Super HAD CCD
410,000 Pixels 470,000 Pixels
380,000 Pixels 440,000 Pixels
525 Lines, 2:1 Interlace 625 Lines, 2:1 Interlace
15.734kHz(H), 59.94Hz(V) 15.625kHz(H), 50Hz(V)
INTERNAL
More than 50dB
0.1lx (F=1.2, 50IRE)
0.001lx (F=1.2, 50IRE, MAX FIELDS x512)
VBS 1.0Vp-p / BNC
MANUAL / DC / VSD
1/60 ~ 1/100,000 sec 1/50 ~ 1/100,000 sec
OFF - 36dB
OFF / BLC / WDR / BMB
AWC LOCK / AWC AUTO / ATW / INDOOR / OUTDOOR / MANUAL
DC12V ± 2V
CS Mount
61.6[W] x 52.4[H] x 77.8[D]mm
Pantone Color 11C (Gray)
Gray
-10°C ~ +50°C
-20°C ~ +70°C
90% RH (non-condensing)
540 TV Lines
NTSC PAL Video Standard
1.5W (max)
181g
VCC-600N VCC-600P MODEL NAME