Specifications, Warning, Assembly – Harbor Freight Tools One Step Gardens Hand Operated Water Pump 1318 User Manual

Page 2: Operation

SKU 01318

For technical questions, please call 1-800-444-3353.

Page 2

SpeciFicatiOnS

Handle

7”

Inlet Pipe Diameter 1-1/4” NPT

Maximum Lift

25 Feet

Maximum Volume 12 oz. Per Stroke

Assembled Dim.

17” H x 8” W

Spout to Handle

12-1/2”

Construction

Cast Iron Body, Base, and Handle

Aluminum Internal Parts

this product can be set up to pump water but

never use this product to pump drinking (potable)

water.

Warning!

Wear ANSI-approved safety goggles during

assembly.
Use for pumping water only.

Warning:

This product contains or, when

used, produces a chemical known to the State

of California to cause cancer and birth defects

or other reproductive harm. (California Health

& Safety Code § 25249.5, et seq.)

aSSembly

Place the

base (13) on a flat, smooth

surface.
Set the

Valve assembly (12) in the circle

groove of the

base (13). It will only fit with the

metal plate up.
Put the

cylinder (9) on the Valve assembly

(12). Line up the cylinder (9) so that the bolt

holders on each side of sit over the two drilled

openings on the

base (13). The spout on the

cylinder (9) should rest over the flat side of

the

base (13).

Slip a

bolt (10) and a Washer (11) into the

bolt holder on the

cylinder (9). Put a nut (14)

under the

base (13) and screw it onto the bolt

(10). Hand tighten. Repeat the procedure

on the other side. Then, wrench tighten both

bolts (10).
Set the

piston assembly (8) with the screw

eyelet up, down into the

cylinder (9).

Put the

cover (5) onto the cylinder (9) so the

screw eyelet on the

piston assembly (8) fits

through the opening in the center of the

cover

(5). The large bolt hole on the cover (5) should

sit opposite the spout on the

cylinder (9). The

two recessed

Screw bolts (4) should straddle

each side of the spout on the

cylinder (9).

Tighten the recessed

Screw bolts (4) with a

small flat screwdriver. With a crescent wrench,

tighten the large

bolt (6) on the cover (5)

opposite the spout.
Attach the

Handle (2) to the piston assembly

(8) using a bolt (3) and nut (1). Make sure

the hole on the

Handle (2) that attaches to the

cover (5) rests between the bolt housing on the

cover (5). If necessary, rotate the screw eyelet

on the

piston assembly (8) to find the best

fit. Tighten the

nut (1). Next, run the bolt (7)

through the bolt housing on the

cover (5) and

the

Handle (2) and tighten the nut (1).

Attach 1-1/4” NPT threaded water source

pipe to the threaded inlet on the bottom of the

pump.
Secure the pump by screwing the base to a

stable surface.

OperatiOn

This pump needs to be primed before every

use. Keep a pitcher (not included) of water near

the pump for this purpose. Pump the handle

up and down while pouring about a quart of

water into the top of the pump to prime it and

start the water flow.

note: dO nOt StOp pumping tHe Handle

until FiniSHed! Stopping, even momentarily,

will cause the pump to lose its prime and no

longer work until primed again.
Refill the pitcher. Then, continue pumping as

needed.

note: do not pump drinking water from this

pump.

reV 02d; 09b