Holmes HASF1650 User Manual

Page 2

P L E A S E R E A D A N D S AV E T H E S E

I M P O R TA N T S A F E T Y I N S T R U C T I O N S

F E AT U R E S - O P E R AT I O N S

C L E A N I N G / M A I N T E N A N C E

When using electrical appliances, basic safety precautions

should always be taken including the following:
1. Read all instructions before using this appliance.

2. Use fan only for purposes described in the instruction

manual.

3. To protect against electrical shock do not immerse unit,

plug or cord in water or spray with liquids and plug the

appliance directly into a electrical outlet.

4. Close supervision is necessary when any appliance is

used by or near children.

5. Unplug from outlet when not in use, when moving fan

from one location to another, before putting on or

taking off parts and before cleaning.

6. Avoid contact with moving parts.

7. Do not operate in the presence of explosive and/or

flammable fumes.

8. To avoid fire hazard, NEVER place the cord under rugs

or any parts near an open flame, cooking or other

heating appliance.

9. Do not operate any appliance with a damaged cord or

plug after the appliance malfunctions, or has been

dropped/damaged in any manner.

10. The use of attachments not recommended or sold by

the appliance manufacturer may cause hazards.

11. Do not let the cord hang over the edge of a table,

counter or come in contact with hot surfaces or leave

exposed to high traffic areas.

12. To disconnect, grip plug and pull from wall outlet.

Never yank on cord.

13. Always use on a dry, level surface.

14. Do not operate fan until fully assembled with all

parts properly in place.

15. This product is intended for household use ONLY and

not for commercial or industrial applications.

16. WARNING: To reduce the risk of fire or electric

shock, DO NOT use this fan with any solid-state speed

control device.

PLEASE READ AND SAVE

THESE IMPORTANT SAFETY

INSTRUCTIONS

ASSEMBLY INSTRUCTIONS

NOTE: MAKE SURE YOU REMOVE ALL CONTENTS OF THE

PACKAGE. PLEASE CHECK PACKAGING MATERIALS FOR

PARTS THAT COULD BE REQUIRED TO ASSEMBLE YOUR FAN.
Base/Pole Assembly
You will need the base, Round Weight, pole assembly,

pole ring, washer and L-shaped locking lever

(See Figure 1-2).
1. Slide the bottom end of the outer pole through the

pole ring.

2. Turn the base upside down and place the weighted

insert and washer into the base cover.

3. Secure the base and round weight to the bottom of

the outer pole using the L-shaped locking lever and

washer.

4. Turn the L-shaped locking lever clockwise to securely

attach the pole to the base.

5. Set the base on the floor, weight side down. Push the

pole ring down until it sits directly on the base.

Fan Head Assembly
You are now ready to assemble the fan head

(See Figure 1-2).

1. Position the Rear Grill over the Motor Shaft, making

certain the notches at the top and bottom of the Rear

Grill fit over the prongs on the Motor Housing. Please

make sure the Rear Grill fits securely against the

motor housing.

2. Secure the rear grill in its place using the rear grill

mounting nut. Turn this nut clockwise and tighten

firmly.

3. Slide the fan blade, with the hollowed interior of the

blade facing toward the rear grill, firmly onto the

motor shaft. The top of the motor shaft should lie

even with the center of the fan blade.

4. Line up the hole on the shaft of the fan blade with

the notch on the motor shaft.

5. After aligning the holes, secure the fan blade to the

motor shaft by tightening the securing screw with a

Phillips head screw driver.

NOTE: The securing screw is not intended to sit flush

when securing the blade.

6. Center the front grill by aligning the Holmes

logo

on the logo plate so it is horizontal and parallel with

the floor. Then, holding the front grill against the

rear grill, push the grill ring into place at the top and

bottom of the fan. (Push directly on the grill ring,

not on the grills themselves). Finish securing the grill

ring in the same manner until both grills are joined

underneath the ring.

Final Assembly
First slide the inner pole extension up from the outer

pole. Insert the pole locking knob into the hole on the

outer pole to securely hold this position. Next, place the

fan head assembly into this extension pole, inserting the

neck of the fan into the pole opening. Turn the fan

head’s neck until the head is securely locked into place.

Finally, add the tilt adjustment knob to the hole of the

fan head’s neck. Tighten when fan head is in your

desired position.

This product is for use on 120 volts. The cord has a plug (A) as shown. An

adapter (C) is available for connecting three-blade grounding-type plugs to two-

slot receptacles (B). The green grounding lug extending from the adapter must

be connected to a permanent ground such as a properly grounded outlet box.

The adapter should not be used if a three-slot grounded receptacle is available.
CAUTION: Use Only with GFCI Protected Receptacles.

Figure 1

A. Front Grill

B. Front Grill Ring

C. Fan Blade

D. Securing Screw

E. Mounting Nut

F. Rear Grill

G. Motor Shaft

H. Motor Housing

I. Tilt Adjustment Knob

J. Fan Head Neck

K. Inner Pole

L. Pole Lock Knob

M. Outer Pole

N. Pole Ring

O. Base

P. Round Weight

(not shown)

Q. L-Shaped Locking

Lever

R. Washer (Refer to

Figure 2)

Figure 2

OPERATING INSTRUCTIONS

Your fan is UL approved and safe to be used Indoors or

Outdoors. Outdoor applications provide a cool, refreshing

breeze on hot stagnant days as well as warding off

annoying insects or barbecue smoke.
1. Set fan base on a dry, level surface.

2. Plug cord into any standard 120 volt AC outlet.

Please make sure the Selector (Speed) Control is in

the OFF position. Selector (Speed) Control is located

at the rear of the Fan Motor Housing.

3. The SPEED is adjusted by turning the control knob to

the desired setting, OFF-III-II-I.

4. The Oscillation Control Knob is located on the top of

the Fan Motor Housing. To start Oscillation, push

control knob down. To Stop Oscillation, pull control

knob up.

ADJUSTMENT INSTRUCTIONS

Tilt-Adjustment
Follow these instructions to tilt the Fan Head for upward

angle air movement.
1. To change the tilting angle of the fan head, simply

loosen the Tilt-Adjustment Knob.

2. Move the fan head to the desired angle and firmly

tighten the Tilt-Adjustment Knob to lock into place.

Height Adjustment
Follow these instructions to adjust the height of the fan.
1. Turn the pole locking knob counter-clockwise to

loosen the pole.

2. Adjust the pole to the desired height and firmly tighten

the Pole Locking Knob in a clockwise direction.

CLEANING/MAINTENANCE INSTRUCTIONS

Follow these instructions to correctly and safely care for

your fan. Please remember:
• Always unplug the fan before cleaning or

disassembling.

• Do not allow water to drip on or into the fan motor

housing.

• Do not use any of the following as a cleaner:

gasoline, thinner, benzene.

Fan Blade Cleaning
1. To access the fan blade, remove the front grill and

securing screw.

2. Clean the fan blade, front and rear grills with a soft,

moist cloth.

3. Replace blade, tighten securing screw and securely

fasten the front grill.

Fan Head, Base and Pole Cleaning
Using a soft, moist cloth, with or without a mild soap

solution, carefully clean the fan base, pole and head.

Please use caution around the motor housing area. Do

not allow the motor or other electrical components to be

exposed to water.

FAN STORAGE INSTRUCTIONS

Your fan should be stored in the off-season in its original

box. It is important to keep it in a safe, dry location.
• We recommend using the original (or appropriately

sized) box.

• Please remember to protect the fan from dust or

moisture.

If you have any questions regarding your product or

would like to learn more about other Holmes

products, please contact our Consumer Service

Department at 1-800-546-5637 or visit our website at

www.holmesproducts.com

HASF1650_07EM1.qxd 10/13/07 9:43 AM Page 2