beautypg.com

Operation, Basic operation, Source selection – Harman-Kardon 13828 User Manual

Page 19: Controls and use of headphones, Surround mode selection

background image

ENGLISH

OPERATION 19

Operation

Basic Operation

Once you have completed the setup and
configuration of the AVR, it is simple to operate
and enjoy. The following instructions should be
followed for you to maximize your enjoyment of
your new receiver:

Turning the AVR On or Off
• When using the AVR for the first time, you must
press the Main Power Switch

0 on the front

panel to turn the unit on. This places the unit in a
Standby mode, as indicated by the orange color of
the Power Indicator

2. Once the unit is in

Standby, you may begin a listening session by
pressing the System Power Control

1 or the

Source button

A on the front panel or the AVR

Selector

h. Note that the Power Indicator

2 will turn blue.This will turn the unit on and
return it to the input source that was last used.
The unit may also be turned on from Standby by
pressing any of the Source Selector buttons on
the remote

5gh.

NOTE: After pressing the the DVD Button

5

to turn the unit on, press the AVR Selector

h

to have the remote control all of the AVR func-
tions.

To turn the unit off at the end of a listening
session, simply press the System Power
Control

1 on the front panel or the Power

Off Button

3 on the remote.

When the remote is used to turn the unit “off” it
is actually placing the system in a Standby mode,
as indicated by the orange color of the Power
Indicator

2.

When you will be away from home for an
extended period of time it is always a good idea
to completely turn the unit off with the front
panel Main Power Switch

0.

NOTE: All preset memories may be lost if the
unit is left turned off with the Main Power
Switch

0 for more than two weeks.

Using the Sleep Timer
• To program the AVR for automatic turn-off,
press the Sleep Button

d on the remote. Each

press of the button will increase the time before
shut down in the following sequence:

When the programmed sleep time has elapsed,
the unit will automatically turn off (to Standby
mode). Note that the front panel display will dim
to one half brightness when the Sleep function
is programmed. To cancel the Sleep function,
press and hold the Sleep Button

d until the

information display returns to normal brightness
and the

SLEEP OFF

message appears in the

Main Information Display

F.

Source Selection

• To select a source, press any of the
Source Selector buttons on the remote
5gh.

NOTE: After pressing the DVD Button

5 you

must press the AVR Selector

h to have the

remote control all of the AVR functions.

• The input source may also be changed by
pressing the front-panel Input Source
Selector
button

A. Each press of the button

will move the input selection through the list of
available inputs.

• As the input is changed, the AVR will auto-
matically switch to the digital input (if selected),
surround mode and speaker configuration that
were entered during the configuration process
for that source.

• The front-panel Video 3 Inputs

H, Optical

Digital 3 Input

4 or the Coaxial Digital 3

Input

G may be used to connect a device such

as a video game or camcorder to your home
entertainment system on a temporary basis.

• As the input source is changed, the new input
name will appear in the Main Information
Display

F and a green LED will light next to

the selected input’s name in the front-panel
Input Indicators

J.

• When a pure audio input (CD, Tuner, Tape,
6/8 Channel Input) is selected, the last video
input used remains routed to the Video Out-
puts

4I and Video Monitor Output B.

This permits simultaneous viewing and listening
to different sources.

• When a Video source is selected, its audio
signal will be fed to the speakers and the video
signal for that input will be routed to the
appropriate Monitor Output Jack

B and will

be viewable on a TV monitor connected to the
AVR. If a component video source is connected to
the Video 1

F or Video 2 8 Component

Inputs, it will be routed to the Component
Video Outputs

E. Make certain that your TV is

set to the proper input to view the appropriate
video signal (composite, S-Video or component
video, see Notes for S-Video on page 13).

Controls and Use of Headphones

• Adjust the volume to a comfortable level using
the front panel Volume Control

I or remote

Volume Up/Down

7 buttons.

• To temporarily silence all speaker outputs
press the Mute button

4. This will interrupt

the output to all speakers and the headphone
jack, but it will not affect any recording or
dubbing that may be in progress. Press the
Mute button

4 again to return to normal

operation.

• During a listening session you may wish to
adjust the Bass Control and Treble Control
to suit your listening tastes or room acoustics.

• To set the output of the AVR so that the out-
put is “flat,” with the Tone controls de-activated,
press the Tone Mode button

T button once

or twice so that the words

Tone Out

appear

momentarily in the Main Information Display
F. To return the tone controls to an active con-
dition, press the Tone Mode

T button once

or twice so that the words

Tone I n

momen-

tarily appear in the Main Information Display
F.

• To change the Bass or Treble Control settings
press the Tone Mode Button

T until the

words Bass or Treble appear momentarily in the
Main Information Display

F. Press the OK

Button

A followed by the

A

/

B

Buttons

Z

to adjust the setting. When done, press the Tone
Mode Button

T again to exit the Tone Mode

Menu.

• For private listening, plug the 6.3 mm stereo
phone plug from a pair of stereo headphones
into the front panel Headphone Jack

3. Note

that when the headphone’s plug is connected,
the word

HEADPHONE

will scroll once across

the Main Information Display

F and all

speakers will be silenced. When the headphone
plug is removed, the audio feed to the speakers
will be restored.

• When the headphones are in use, you may
take advantage of the Dolby Headphone modes
to bring added spaciousness to headphone
listening. Press the Dolby Mode Select
Button

Q or the Surround Mode Group

Selector

6 to cycle through the three Dolby

Headphone modes to select the one that you
prefer.

Surround Mode Selection

One of the most important features of the AVR is
its ability to reproduce a full multichannel
surround sound field from digital sources, analog
matrix surround encoded programs and standard
stereo or even mono programs. In all, a total of
fifteen listening modes are available on the AVR.

Selection of a surround mode is based on
personal taste, as well as the type of program
source material being used.

For example, motion pictures, CD’s or TV
programs bearing the logo of one of the major
surround encoding processes, such as Dolby
Surround should be played in either the Dolby
Pro Logic II Movie (with movies) or Music (with
music) surround mode or with the
Harman Kardon´s exclusive Logic 7 Movie Mode,
to create a full range discrete 5.1 channel
surround signal from surround encoded
programs with a stereophonic left and right rear
signal, just as it was recorded in real life (e.g.

90

min

80

min

70

min

60

min

50

min

40

min

30

min

20

min

10

min

OFF

38277_AVR138_DVD28_ENG 23/07/08 18:36 Side 19