Harbor Freight Tools Rechargeable/Cordless Shaver 66342 - Manual (Page 2)

SKU 66342 For technical questions, please call 1-800-444-3353. Page 2
specIFIcatIons
Charging Time 5-7 Hours
Speed
9000 OPM
(Oscillations Per Minute)
Charger Input 3VDC
Internal Battery Ni-Cd
unpackInG
When unpacking, make sure that the item
is intact and undamaged. If any parts are missing
or broken, please call Harbor Freight Tools at the
number shown on the cover of this document as
soon as possible.
Important saFetY
InFormatIon
Do not expose to moisture while charging. 1.
Do not reach for a plugged in Shaver that 2.
has fallen into water. Unplug immediately
and drain water.
Do not charge near heater or in direct sun-
3.
light.
Do not use if Charger (5) or Charger cord
4.
has been damaged.
Do not attempt to remove Foil covering with
5.
screwdriver or other tools.
Do not use without Foil (2) and Foil Holder
6.
(3) in place.
This product is not a toy. Do not allow chil-
7.
dren to play with this item.
Use as intended only.
8.
Inspect before every use; do not use if parts 9.
are loose or damaged.
Turn off Shaver before charging.
10.
Do not charge immediately after prolonged 11.
use. Allow it to cool before charging.
Rinse off Shaver after each use and keep
12.
stored in dry, cool environment out of chil-
dren’s reach.
Maintain product labels and nameplates.
13.
These carry important safety information.
If unreadable or missing, contact Harbor
Freight Tools for a replacement.
read the entIre Important
saFetY InFormatIon section at the
beginning of this document including
all text under subheadings therein
before set up or use of this product.
cHarGInG InstructIons
Attach the power cord of the Charger (5) into 1.
the bottom of the Shaver (1). Plug the Char-
ger into an electrical outlet that is away from
a sink or other source of water. note: Make
sure Shaver Switch (8) is turned to OFF.
Once plugged in, the LED Charger light on
2.
the front of Shaver housing will activate.
Charge for 5 to 7 hours. Do not charge for
3.
longer than required charge time.
operatIon InstructIons
Once fully charged, remove Charger cord 1.
from housing, remove Cover (4) and turn
Switch to ON.
Gently guide Shaver along face and chin to
2.
remove beard. Use short, back and forth
strokes. Note: Do not apply too much pres-
sure while shaving.
If you have not used an electric shaver
3.
before, your skin may become irritated after
use. This is a natural reaction that may
last for a few days until your skin adjusts to
Shaver.
When finished shaving, turn Switch to OFF.
4.
Slide the Cover onto Shaver head until ready 5.
to use again. For travelling purposes, slide
the Shaver into the Carrying Sleeve (7).
cleanInG tHe sHaVer
After each use, beard and hair cuttings may 1.
collect in Foil. Clean Foil by rinsing Shaver
head under cool running water.
WarnInG!
2. Only clean when Shaver is dis-
connected from Charger and switch is turned
to OFF.
Hair trimmings may get under Foil and/or
3.
it may be necessary to replace Foil. First,
press down on the tabs on either side of the
Foil Holder (3).
Slide Foil Holder off of the top of Shaver
4.
housing, exposing the Shaver cutting heads.