Hasbro Biscuit My Lovin Pup 77698 - Manual (Page 2)

Note to the consumer: To install batteries in
your puppy, lay him down on his back first.
This will make the installation process much
easier.
CAUTION: TO AVOID BATTERY LEAKAGE
1. Be sure to insert the batteries correctly and always
follow the toy and battery manufacturers’ instructions;
2. Do not mix old batteries and new batteries or
alkaline,
standard (carbon-zinc) or rechargeable (nickel-
cadmium) batteries;
3. Always remove weak or dead batteries from the
product.
IMPORTANT: BATTERY INFORMATION
Please retain this information for future reference.
Batteries should be replaced by an adult.
CAUTION:
1. Always follow the instructions carefully. Use only batteries
specified and be sure to insert item correctly by matching the +
and – polarity markings.
2. Do not mix old batteries and new batteries or standard (carbon-
zinc) with alkaline batteries.
3. Remove exhausted or dead batteries from the product.
4. Remove batteries if product is not to be played with for a long
time.
5. Do not short-circuit the supply terminals.
6. Should this product cause, or be affected by, local electrical
interference, move it away from other electrical equipment.
Reset (switching off and back on again or removing and re-
inserting batteries) if necessary.
7. RECHARGEABLE BATTERIES: Do not mix these with any other
types of batteries. Always remove from the product before
recharging. Recharge batteries under adult supervision. DO
NOT RECHARGE OTHER TYPES OF BATTERIES.
TO INSTALL BATTERIES
Place door back over
batteries. Push down
on door; hold door
down with one hand
and use other hand to
tighten screw.
NOTE: The toy uses battery power whenever
switch is in the “ON” position. To conserve
batteries, move switch to “OFF” position when
you’re not playing with your puppy.
GETTING STARTED
The first thing you need to do when you take
your BISCUIT puppy out of the box is to insert
batteries.
Use a Phillips/cross
head screwdriver (not
included) to loosen
screw in battery
compartment (screw
remains attached). Take
off the door and insert 6
x 1.5V “D” or LR20 size
alkaline batteries.
CLEANING INSTRUCTIONS
To clean your puppy, gently brush him with a cloth or soft brush to loosen any dirt. Then use a
slightly damp cloth to remove stains.
• To prevent staining, wipe off dirt immediately.
• Do not get wet; to remove stains use only a slightly damp cloth.
• Do not use detergent or stain removers.
• If puppy gets wet, remove batteries and let dry; once puppy is completely dry, replace batteries.
•
Avoid spilling food or beverages on the puppy.
• Do not throw or kick the puppy, and do not push sharp objects through the speaker openings.
• Do not leave puppy in direct sunlight; high temperatures will destroy the mechanism.
PLAYING OPTIONS
Play Mode
Biscuit responds to your touch and your voice. The
more you play with him, the happier he will be!
Response Mode
If Biscuit hears speech that is not a speech
command, he’ll respond with puppy sounds.
Hangout Mode
After a few moments of non-activation, Biscuit will
enter hangout mode. He will move his head a little,
blink and twitch his ears. He will whine or bark a
little to get your attention!
After a few minutes in hangout mode, your
puppy will go to “sleep”: he’ll lay down and
start snoring! If the room is dark or dimly lit,
Biscuit will go to “sleep” much faster than if
the room is bright.
To “wake” him, and return to Play Mode, clap
twice or wave your hand over his forehead.
LIGHT SENSOR FEATURE
If it is dark in the room and the lights come
on suddenly while your puppy is “asleep”,
he’ll lift his head and open his eyes and make
a little mumbling noise. If you don’t pet your
puppy within about 10 seconds, he will go
back to “sleep”.
1 6