Holmes HAOF12R User Manual

Page 2

OPERATING INSTRUCTIONS

Step 1: Set the fan base on a dry, level surface.

Step 2: Please make sure the speed control knob is in the off posi-

tion. Plug cord into any standard 120 volt A/C outlet.

Step 3: The SPEED is adjusted by moving the knob left or right to

one of the 3 desired settings (High, Med., and Low).

Step 4: The OSCILLATION control knob is located on the top of the

fan motor housing. To start oscillation, push control knob

down. To stop oscillation, pull control knob up.

ADJUSTMENT INSTRUCTIONS

Tilt Adjustment:
Step 1: Loosen the tilt-adjustment knob and move the fan head to the

desired angle. Once your fan is at the appropriate angle, tighten

the knob by turning clockwise.

CLEANING/MAINTENANCE INSTRUCTIONS

Follow these instructions to correctly and safely care for your Holmes

table fan. Please remember:

• Always unplug the fan before cleaning or disassembling.
• Do not allow water to drip on or into the fan motor housing.
• Do not use any of the following as a cleaner: gasoline, thinner,

or benzine.

Step 1: To access the fan blade, remove the front grill and then

unscrew the securing screw on the fan blade.

Step 2: Clean the fan blade, both front and rear grills with a soft

cloth moistened with a mild soap solution.

Step 3: Replace blade, tighten the fan blade by screwing the fan

blade back on, and securely fasten the front grill.

Fan Head and Base Cleaning

Using a soft, moist cloth, with or without a mild soap solution, care-

fully clean the fan base and head. Please use caution around the

motor housing area. Do not allow the motor or other electrical com-

ponents to be exposed to water.

FAN STORAGE

Your fan should be stored in the off-season fully assembled and we

recommend using the original (or appropriately sized) box. It is

important to keep it in a safe, dry location.
• Remember to protect the fan head from dust or moisture.

PLEASE READ AND SAVE

THESE IMPORTANT

SAFETY INSTRUCTIONS

When using electrical appliances, basic safety precautions should

always be followed to reduce the risk of fire, electric shock, and

injury to persons, including the following:

1) Read all instructions before using the appliance.
2) To avoid fire or shock hazard, plug the appliance directly into a

120 V AC electrical outlet.

3) Keep the cord out of heavy traffic areas. DO NOT let the cord

hang over the edge of a table or counter. To avoid fire hazard,

NEVER put the cord under rugs, near heat registers, radiator,

stoves, or heaters.

4) To protect against electrical hazards, DO NOT immerse in water

or other liquids. Do not use near water.

5) Close supervision is necessary when any appliance is used by or

near children, or by disabled people.

6) Always unplug the fan before moving it, putting on or taking off

parts, cleaning, or whenever the fan is not in use. Be sure to

pull by the plug and not the cord.

7) Avoid contact with moving parts. DO NOT operate without fan

grills properly in place.

8) DO NOT operate any appliance with a damaged cord or plug,

if motor fan fails to rotate, after the appliance malfunctions,

or if it has been dropped or damaged in any manner. Return

appliance to manufacturer for examination, electrical or

mechanical adjustment, or repair.

9) DO NOT operate in the presence of explosive and/or flammable

fumes.

10) Use appliance only for intended household use as described in this

manual. Any other use not recommended by the manufacturer

may cause fire, electric shock, or injury to persons. The use of

attachments not recommended or sold by The Holmes Group may

cause hazards.

11) DO NOT use outdoors.
12) Always use on a dry, level surface.
13) Keep unit away from heated surfaces and open flames.
14) WARNING: To reduce the risk of fire or electric shock, DO NOT

use this fan with any solid-state speed control device.

15) DO NOT attempt to repair or adjust any electrical or mechanical

functions on this unit. Doing so will void your warranty. The

inside of the unit contains no user serviceable parts. All servicing

should be performed by qualified personnel only.

PLEASE READ AND SAVE

THESE IMPORTANT

SAFETY INSTRUCTIONS

ASSEMBLY INSTRUCTIONS

Your table fan comes completely assembled and is ready for

immediate use. Carefully unpack your fan, plug it in and enjoy.

FIGURE 2

A. FRONT GRILL
B. REAR GRILL (SEE FIGURE 2)
C. LOGO PLATE
D. FAN BLADE
E. CARRY HANDLE

(SEE FIGURE 2)

F. SPEED CONTROL KNOB

(SEE FIGURE 2)

G. OSCILATION CONTROL

KNOB (SEE FIGURE 2)

H. TILT ADJUSTMENT KNOB

(SEE FIGURE 2)

I. BASE

FIGURE 1

THIS PRODUCT IS EQUIPPED WITH A POLARIZED AC

(Alternating Current) PLUG (a plug having one blade

wider than the other). This plug will fit into the power

outlet only one way. If the plug does not fit fully into the

outlet, reverse the plug. If it still does not fit, contact

qualified personnel to install the proper outlet.

DO NOT DEFEAT THE SAFETY PURPOSE OF THIS

POLARIZED PLUG IN ANY WAY