beautypg.com

Holmes HACP9 User Manual

Page 2

background image

P L E A S E R E A D A N D S AV E T H E S E

I M P O R TA N T S A F E T Y I N S T R U C T I O N S

F E AT U R E S - O P E R AT I O N S

Thank you for purchasing this Holmes

®

product. We

understand the value of quality and are committed to

making superior products that stand the test of time. We

trust this product will exceed your expectations of quality

and reliability. We hope that you enjoy this product and

will consider purchasing another Holmes

®

product in the

future. To see our full product line or if you have any

questions or comments about this product, please visit our

website at: www.holmesproducts.com.
When using electrical appliances, basic safety precautions

should always be taken including the following:
1. Read all instructions before using this appliance.

2. Use fan only for purposes described in the instruction

manual.

3. To protect against electrical shock do not immerse unit,

plug or cord in water or spray with liquids. Plug the

appliance directly into a 120V AC electrical outlet.

4. WARNING: To reduce the risk of fire or electrical

shock, DO NOT use this fan with any solid-state speed

control device.

5. Close supervision is necessary when any appliance is

used by or near children.

6. Unplug from outlet when not in use, when moving fan

from one location to another, before putting on or

taking off parts and before cleaning.

7. Avoid contact with moving parts.

8. DO NOT operate in the presence of explosives and/or

flammable fumes.

9. To avoid fire hazard, NEVER place the cord under rugs

or any parts near an open flame, cooking or other

heating appliance.

10. DO NOT operate any appliance with a damaged cord

or plug after the appliance malfunctions, or has been

dropped/damaged in any manner.

11. The use of attachments not recommended or sold by

the appliance manufacturer may cause hazards.

12. DO NOT use outdoors.

13. DO NOT let the cord hang over the edge of a table,

counter or come in contact with hot surfaces or leave

exposed to high traffic areas.

14. To disconnect, grip plug and pull from wall outlet.

Never yank on cord.

15. Always use on a dry, level surface.

16. DO NOT operate fan until fully assembled with all

parts properly in place.

17. This product is intended for household use only and

not for commercial or industrial applications.

PLEASE READ AND SAVE

THESE IMPORTANT

SAFETY INSTRUCTIONS

PRE-OPERATING INSTRUCTIONS

THIS HACP9 OSCILLATING CLIP FAN COMES FULLY

ASSEMBLED AND IS READY FOR IMMEDIATE USE.

OPERATING INSTRUCTIONS

1. Clip fan onto a dry, level surface.

2. Please make sure the On/Speed switch is in the "Off"

position. Plug the cord into any standard 120-volt A/C

outlet.

3. The SPEED is adjusted by moving the switch left or

right to the desired setting.

4. The OSCILLATION control knob is located on the top of

the fan motor housing. To start oscillation, push control

knob down. To stop oscillation, pull control knob up.

WALL MOUNTING INSTRUCTIONS

NOTE: On the underside of the fan’s clip there are “KEY

SLOTS” (2).
Select a suitable spot on a wall (away from curtains,

draperies, or heat sources) where you want to mount the

fan. Use a No. 10 pan head wood screw (1 1/4” length)

and thread into a 2x4 wood stud behind the dry wall.

Please refer to the warning below if you are unable to

locate a wood stud in the wall.
When threading the screw into the wall, leave

approximately 1/4” clearance between the screw and wall.

This will allow the clip’s “KEY SLOTS” to fit easily and

securely over the screws. If necessary, the screw may be

tightened further to ensure the fan is firmly attached to the

wall.
WARNING: WHEN MOUNTING THE FAN TO PLASTER,

DRYWALL OR SHEETROCK, YOU MUST USE A MOLLY BOLT,

OR SIMILAR FASTENER. DOING SO WILL PREVENT THE FAN

FROM BECOMING DISLODGED WHILE IN OPERATION.

ADJUSTMENT INSTRUCTIONS

Vertical Angle Adjustment
1. To change the tilting angle of the fan head, simply

loosen the tilt adjustment knob.

2. Move the fan head to the desired angle, then firmly

tighten the knob to lock the fan head in place.

Horizontal Angle Adjustment
Turn the motor housing to the desired direction.
WARNING: MAKE SURE TO SUPPORT THE FAN HEAD

ASSEMBLY WHEN LOOSENING THE ADJUSTABLE HEIGHT

NUT, AS THE WEIGHT OF THE FAN HEAD MAY CAUSE THE

EXTENSION POLE TO COLLAPSE.

CLEANING/MAINTENANCE

Follow these instructions to correctly and safely care for

your oscillating clip fan. Please remember:
• Always unplug the fan before cleaning or

disassembling.

• Do not allow water to drip on or into the fan motor

housing.

• Do not use any of the following as a cleaner: gasoline,

thinner, benzene.

1. To access the fan blade, remove the front grill by

pressing the tabs on the grill ring away from the fan.

2. Clean the fan blade, both front and rear grills with a

soft cloth moistened with a mild soap solution.

NOTE: FAN BLADE SHOULD NOT BE REMOVED.

3. Replace the front grill by snapping back into rear grill.

Fan Head and Clip Cleaning
Using a soft, moist cloth, with or without a mild soap

solution, carefully clean the fan head. Please use caution

around the motor housing area. Do not allow the motor or

other electrical components to be exposed to water.

FAN STORAGE

In the off-season:
IMPORTANT: Keep your fan in a safe dry location,

where the fan is not likely to fall or be crushed.

• Your fan should be stored fully assembled.

• Remember to protect the fan head from dust or

moisture.

THIS APPLIANCE HAS A POLARIZED PLUG (one blade is wider than the

other). To reduce the risk of electric shock, this plug is intended to fit in

a polarized outlet only one way. If the plug does not fit fully in the

outlet, reverse the plug. If it still does not fit, contact a qualified

electrician to install the proper outlet.

DO NOT ATTEMPT TO MODIFY THIS PLUG OR DEFEAT THIS

SAFETY FEATURE IN ANY WAY.

C L E A N I N G / S T O R A G E

A

B

C

D

E

F

FIGURE 1

A. Front Grill

B. Fan Blade

C. Power Cord

D. Key Slots (underside

of clip)

E. Pivot Caps (2)

F. Clip

G. Clamp Pivot

H. Pivot Bracket

I. Motor Housing

J. Oscillation Knob

K. Rear Grill

L. Tilt Adjustment Knob

G

H

I

J

K

L

HACP906EM1.qxd 10/16/06 14:25 Page 2